Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Separate Seat Type)

DTC    B1780    Front Occupant Classification Sensor LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification sensor front LH circuit consists of the occupant classification ECU and the occupant classification sensor front LH.
DTC B1780 is set when a malfunction is detected in the occupant classification sensor front LH circuit.

DTC No.
DTC Detecting Conditions
Trouble Areas
B1780
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification sensor front LH circuit for 2 seconds
  2. Occupant classification sensor front LH malfunction
  3. Occupant classification ECU malfunction
  1. Front seat with adjuster frame assembly RH (Occupant classification sensor front LH)
  2. No. 1 seat wire
  3. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting the supplemental restraint system, perform troubleshooting for DTC B1780 of the occupant classification system.
  2. Use the intelligent tester to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.


WIRING DIAGRAM


H100921E07


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat assembly installation bolts to see the under surface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

HINT:
  1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  2. Use the intelligent tester to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1780 is not output.

HINT:
DTCs other than B1780 may be output at this time, but they are not related to this check.



OK
PERFORM SENSITIVITY CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the occupant classification sensor front LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the occupant classification ECU side and occupant classification sensor front LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.CHECK NO. 1 SEAT WIRE (TO B+)


    H100210E02
  1. Disconnect the connectors from the occupant classification ECU and the occupant classification sensor front LH.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (SGD1) - Body ground
    Ignition switch ON
    Below 1 V
    O4-7 (SIG1) - Body ground
    Ignition switch ON
    Below 1 V
    O4-11 (SVC1) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


5.CHECK NO. 1 SEAT WIRE (FOR OPEN)


    H100920E05
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using service wires, connect O6-1 (SVC1) and O6-3 (SGD1), and connect O6-2 (SIG1) and O6-3 (SGD1) of connector C.

NOTICE:
Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-7 (SIG1) - O4-1 (SGD1)
    Always
    Below 1 Ω
    O4-11 (SVC1) - O4-1 (SGD1)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


6.CHECK NO. 1 SEAT WIRE (FOR SHORT)


    H100210E02
  1. Disconnect the service wires from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-7 (SIG1) - O4-1 (SGD1)
    Always
    1 MΩ or higher
    O4-11 (SVC1) - O4-1 (SGD1)
    Always
    1 MΩ or higher
    O4-7 (SIG1) - O4-11 (SVC1)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


7.CHECK NO. 1 SEAT WIRE (TO GROUND)
H100210E02
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (SGD1) - Body ground
    Always
    1 MΩ or higher
    O4-7 (SIG1) - Body ground
    Always
    1 MΩ or higher
    O4-11 (SVC1) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


8.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the occupant classification sensor front LH.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

HINT:
  1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  2. Use the intelligent tester to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1780 is not output.

HINT:
DTCs other than B1780 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.



NG
Go to step 13
OK


11.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 13
OK


12.CHECK DTC
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

HINT:
  1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
  2. Use the intelligent tester to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1780 is not output.

HINT:
DTCs other than B1780 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


13.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY RH
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat with adjuster frame assembly RH (Click here).


NEXT


14.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.


NEXT


15.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

USE SIMULATION METHOD TO CHECK