DTC B1790 Center Airbag Sensor Assembly Communication Circuit Malfunction |
| DTC No. | DTC Detections Conditions | Trouble Areas |
| B1790 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECT CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor assembly.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and occupant classification ECU side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (FOR OPEN) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect O5-8 (FSR+) and O5-4 (FSR-) of connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-12 (FSP+) - A23-13 (FSP-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-12 (FSP+) - A23-13 (FSP-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A23-12 (FSP+) - Body ground | Ignition switch ON | Below 1 V |
| A23-13 (FSP-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK AIRBAG SENSOR ASSEMBLY CENTER COMMUNICATION CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-12 (FSP+) - Body ground | Always | 1 MΩ or higher |
| A23-13 (FSP-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK DTC |
Connect the connectors to the occupant classification ECU and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| NG | |
| 9.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 10.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Using the intelligent tester, perform the zero point calibration (Click here).
| NEXT | |
| 11.PERFORM SENSITIVITY CHECK |
Using the intelligent tester, perform the sensitivity check (Click here).
| NEXT | |
| 12.CHECK DTC |
Connect the connector to the occupant classification ECU.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 13.CHECK NO. 1 SEAT WIRE (FOR OPEN) |
![]() |
Disconnect the No.1 seat wire connector from the occupant classification ECU.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| BH1-5 (FSP+) - BH1-6 (FSP-) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 14.CHECK NO. 1 SEAT WIRE (FOR SHORT) |
![]() |
Disconnect the No.1 seat wire connector from the occupant classification ECU.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| BH1-5 (FSP+) - BH1-6 (FSP-) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 15.CHECK NO. 1 SEAT WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the No. 1 seat wire connector from the occupant classification ECU.
Disconnect the connector from the occupant classification ECU.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| BH1-5 (FSP+) - Body ground | Ignition switch ON | Below 1 V |
| BH1-6 (FSP-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 16.CHECK NO. 1 SEAT WIRE (TO GROUND) |
![]() |
Disconnect the No. 1 seat wire connector from the occupant classification ECU.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| BH1-5 (FSP+) - Body ground | Always | 1 MΩ or higher |
| BH1-6 (FSP-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||