Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1651/33    Manual Cut off Switch Trouble

for Preparation Click here


DESCRIPTION

The airbag cut-off switch circuit consists of the center airbag sensor assembly and the airbag cut off switch.
DTC B1651/33 is set when a malfunction is detected in the airbag cut off switch circuit.

DTC No.
DTC Detecting Conditions
Trouble Areas
B1651/31
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the airbag cut off switch circuit for 2 seconds
  2. Airbag cut off switch malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Airbag cut-off switch
  3. Center airbag sensor assembly

WIRING DIAGRAM


H100906E03


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  1. (j) Disconnect the connector from the front seat outer belt assembly LH.
  2. (k) Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  3. (f) Disconnect the connector from the front seat airbag assembly LH.
  4. (g) Disconnect the connector from the front seat airbag assembly RH.
  5. (h) Disconnect the connector from the curtain shield airbag assembly LH.
  6. (i) Disconnect the connector from the curtain shield airbag assembly RH.
1.CHECK DTC


    H101852E01
  1. Turn the ignition switch to the ON position.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1651/33 is not output.

HINT:
DTCs other than B1651/33 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the airbag cut off switch.

    OK:
    The connectors are properly connected.



NG
CONNECTION OF CONNECTORS
OK


3.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and airbag cut-off switch side) are not damaged (Click here).



NG
REPAIR OR REPLACE WIRE HARNESS
OK


4.INSPECT AIRBAG CUT-OFF SWITCH


    H046215E01
  1. Disconnect the A20 airbag cut-off switch connector.

  1. Measure the resistance.

    Standard resistance:
    Switch Condition
    Tester Condition
    Specified Condition
    OFF
    1(PMC+) - 2(PMC-)
    80 to 120 Ω
    AUTO
    1(PMC+) - 2(PMC-)
    320 to 480 Ω



NG
REPLACE AIRBAG CUT-OFF SWITCH
OK


5.CHECK INSTRUMENT PANEL WIRE (FOR OPEN)


    H100193E03
  1. Disconnect the instrument panel wire connector from the airbag cut off switch.

  1. Using a service wire, connect A20-1 (PMC+) and A20-2 (PMC-) of connector C.

NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - A21-12 (MSW-)
    Always
    Below 1Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK INSTRUMENT PANEL WIRE (FOR SHORT)


    H100192E01
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - A21-12 (MSW-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7.CHECK INSTRUMENT PANEL WIRE (TO B+)


    H100192E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - Body ground
    Ignition switch ON
    Below 1 V
    A21-12 (MSW-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


8.CHECK INSTRUMENT PANEL WIRE (TO GROUND)


    H100192E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - Body ground
    Always
    1 MΩ or Higher
    A21-12 (MSW-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H101852E01
  1. Connect the connectors to the center airbag sensor assembly and airbag cut off switch.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1651/33 is not output.

HINT:
DTCs other than B1651/33 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK