Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Separate Seat Type)

OCCUPANT CLASSIFICATION SYSTEM (for Separate Seat Type) > Trouble in Passenger Airbag ON / OFF Indicator

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator consists of the center airbag sensor assembly, occupant classification ECU, hazard warning switch assembly, and 4 occupant classification sensors. This system controls the passenger airbag deployment according to the occupancy condition of the front passenger seat, and also displays those detected conditions.

WIRING DIAGRAM


H101921E01


INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. (a) Turn the ignition switch to the LOCK position.
  2. (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. (c) Disconnect the connectors from the center airbag sensor assembly.
  4. (d) Disconnect the connectors from the steering pad assembly.
  5. (e) Disconnect the connector from the front passenger airbag assembly.
  6. (f) Disconnect the connector from the front seat outer belt assembly LH.
  7. (g) Disconnect the connector from the front seat outer belt assembly RH.

HINT:
Skip the following steps if side and curtain shield airbags are not fitted.

  1. (h) Disconnect the connector from the front seat airbag assembly LH.
  2. (i) Disconnect the connector from the front seat airbag assembly RH.
  3. (j) Disconnect the connector from the curtain shield airbag assembly LH.
  4. (k) Disconnect the connector from the curtain shield airbag assembly RH.
1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:
    Double cab:

    Front Seat Passenger
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    ON
    OFF
    OFF
    Child seated / Child restrain system set
    OFF
    ON
    OFF
    Vacant
    OFF
    OFF
    OFF
    Except double cab:

    Front Seat Passenger
    Airbag Cut-Off Switch Position
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    AUTO
    ON
    OFF
    OFF
    Adult seated
    OFF
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    AUTO
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    OFF
    OFF
    ON
    OFF
    Vacant
    AUTO
    OFF
    OFF
    OFF
    Vacant
    OFF
    OFF
    ON
    OFF
    Passenger occupant classification system failure
    AUTO
    OFF
    ON
    ON
    Passenger occupant classification system failure
    OFF
    OFF
    ON
    ON



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK DTC
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
GO TO DTC CHART
OK


3.CHECK VEHICLE TYPE
  1. Proceed to the appropriate step according to the seat type.

    Result:

    Vehicle Type
    Proceed to
    Double cab
    A
    Except Double Cab
    B



B
Go to step 14
A


4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:

    Front Seat Passenger
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    ON
    OFF
    OFF
    Child seated / Child restrain system set
    OFF
    ON
    OFF
    Vacant
    OFF
    OFF
    OFF



OK
USE SIMULATION METHOD TO CHECK
NG


5.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, occupant classification ECU, and 4 occupant classification sensors.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


6.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side, occupant classification ECU side and 4 occupant classification sensors side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


7.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.



NG
Go to step 10
OK


8.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 10
OK


9.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:

    Front Seat Passenger
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    ON
    OFF
    OFF
    Child seated / Child restrain system set
    OFF
    ON
    OFF
    Vacant
    OFF
    OFF
    OFF



OK
END
NG


10.REPAIR FRONT SEAT ASSEMBLY (PASSENGER SEAT)
  1. Loosen the 4 installation bolts fixing the front passenger seat, and then re-tighten them to the specified torque.

    Torque:
    37 N*m (375 kgf*cm, 27 ft.*lbf)


NEXT


11.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.



NG
Go to step 31
OK


12.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 31
OK


13.PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:

    Front Seat Passenger
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    ON
    OFF
    OFF
    Child seated / Child restrain system set
    OFF
    ON
    OFF
    Vacant
    OFF
    OFF
    OFF



NG
Go to step 31
OK

END 

14.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:

    Front Seat Passenger
    Passenger Airbag Manual ON/OFF Switch Position
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    AUTO
    ON
    OFF
    OFF
    Adult seated
    OFF
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    AUTO
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    OFF
    OFF
    ON
    OFF
    Vacant
    AUTO
    OFF
    OFF
    OFF
    Vacant
    OFF
    OFF
    ON
    OFF



OK
Go to step 22
NG


15.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.


NEXT


16.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT


17.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:

    Front Seat Passenger
    Passenger Airbag Manual ON/OFF Switch Position
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    AUTO
    ON
    OFF
    OFF
    Adult seated
    OFF
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    AUTO
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    OFF
    OFF
    ON
    OFF
    Vacant
    AUTO
    OFF
    OFF
    OFF
    Vacant
    OFF
    OFF
    ON
    OFF



OK
END
NG


18.REPAIR FRONT SEAT ASSEMBLY (PASSENGER SEAT)
  1. Loosen the 4 installation bolts fixing the front passenger seat, and then re-tighten them to the specified torque.

    Torque:
    37 N*m (375 kgf*cm, 27 ft.*lbf)


NEXT


19.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.



NG
Go to step 22
OK


20.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).



NG
Go to step 22
OK


21.PASSENGER AIRBAG ON/OFF INDICATOR
  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:

    Front Seat Passenger
    Passenger Airbag Manual ON/OFF Switch Position
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    AUTO
    ON
    OFF
    OFF
    Adult seated
    OFF
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    AUTO
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    OFF
    OFF
    ON
    OFF
    Vacant
    AUTO
    OFF
    OFF
    OFF
    Vacant
    OFF
    OFF
    ON
    OFF



OK
END
NG


22.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and airbag cut-off switch.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


23.CHECK CONNECTORS
  1. Check that the connectors (on the center airbag sensor assembly side and airbag cut-off switch side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


24.INSPECT AIRBAG CUT-OFF SWITCH
H046215E01
  1. Disconnect the A20 airbag cut-off switch connector.

  1. Check the resistance.

    Standard resistance:
    Switch Connection
    Tester Condition
    Specified Condition
    OFF
    1 (PMC+) - 2 (PMC-)
    80 to 120Ω
    ON
    1 (PMC+) - 2 (PMC-)
    320 to 480Ω



NG
REPLACE AIRBAG CUT-OFF SWITCH
OK


25.CHECK INSTRUMENT PANEL WIRE (FOR OPEN)
H100193E02
  1. Disconnect the instrument panel wire connector from the airbag cut-off switch.

  1. Using a service wire, connect A20-1 (PMC+) and A20-2 (PMC-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - A21-12 (MSW-)
    Always
    Below 1Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


26.CHECK INSTRUMENT PANEL WIRE (FOR SHORT)
H100192E02
  1. Disconnect the service wire from connector E.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - A21-12 (MSW-)
    Always
    1 MΩ Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


27.CHECK INSTRUMENT PANEL WIRE (TO GROUND)
H100192E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - Body ground
    Always
    1 MΩ Higher
    A21-12 (MSW-) - Body ground
    Always
    1 MΩ Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


28.CHECK INSTRUMENT PANEL WIRE (TO B+)
H100192E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-11 (MSW+) - Body ground
    Ignition switch ON
    Below 1 V
    A21-12 (MSW-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


29.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and 4 occupant classification sensors.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


30.CHECK CONNECTORS
  1. Check that the connectors (on the occupant classification ECU side and 4 occupant classification sensors side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE WIRE HARNESS
OK


31.CHECK NO. 1 SEAT WIRE (OCCUPANT CLASSIFICATION SENSOR FRONT LH CIRCUIT)
H100920E05
H100210E02
  1. Disconnect the connectors from the occupant classification ECU and the occupant classification sensor front LH.

  1. Using service wires, connect O6-1 (SVC1) and O6-3 (SGD1), and connect O6-2 (SIG1) and O6-3 (SGD1) of connector C.

    NOTICE:
    Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-7 (SIG1) - O4-1 (SGD1)
    Always
    Below 1 Ω
    O4-11 (SVC1) - O4-1 (SGD1)
    Always
    Below 1 Ω

  1. Disconnect the service wires from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-7 (SIG1) - O4-1 (SGD1))
    Always
    1MΩ or Higher
    O4-11 (SVC1) - O4-1 (SGD1)
    Always
    1MΩ or Higher
    O4-7 (SIG1) - O4-11 (SVC1)
    Always
    1MΩ or Higher
    O4-1 (SGD1) - Body ground
    Always
    1MΩ or Higher
    O4-7 (SIG1) - Body ground)
    Always
    1MΩ or Higher
    O4-11 (SVC1) - Body ground
    Always
    1MΩ or Higher

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (SGD1) - Body ground
    Ignition switch ON
    Below 1 V
    O4-7 (SIG1) - Body ground
    Ignition switch ON
    Below 1 V
    O4-11 (SVC1) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


32.CHECK NO. 1 SEAT WIRE (OCCUPANT CLASSIFICATION SENSOR FRONT RH CIRCUIT)
H100213E04
H100210E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the occupant classification ECU and the occupant classification sensor front RH.

  1. Using service wires, connect O7-1 (SVC2) and O7-3 (SGD2), and connect O7-2 (SIG2) and O7-3 (SGD2) of connector C.

    NOTICE:
    Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-8 (SIG2) - O4-2 (SGD2)
    Always
    Below 1 Ω
    O4-12 (SVC2) - O4-2 (SGD2)
    Always
    Below 1 Ω

  1. Disconnect the service wires from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-8 (SIG2) - O4-2 (SGD2)
    Always
    1MΩ or Higher
    O4-12 (SVC2) - O4-2 (SGD2)
    Always
    1MΩ or Higher
    O4-8 (SIG2) - O4-12 (SVC2)
    Always
    1MΩ or Higher
    O4-2 (SGD2) - Body ground
    Always
    1MΩ or Higher
    O4-8 (SIG2) - Body ground
    Always
    1MΩ or Higher
    O4-12 (SVC2) - Body ground
    Always
    1MΩ or Higher

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O4-2 (SGD2) - Body ground
    Ignition switch ON
    Below 1 V
    O4-8 (SIG2) - Body ground
    Ignition switch ON
    Below 1 V
    O4-12 (SVC2) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


33.CHECK NO. 1 SEAT WIRE (OCCUPANT CLASSIFICATION SENSOR REAR LH CIRCUIT)
H100213E03
H100210E06
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the occupant classification ECU and the occupant classification sensor rear LH.

  1. Using service wires, connect O8-1 (SVC3) and O8-3 (SGD3), and connect O8-2 (SIG3) and O8-3 (SGD3) of connector C.

    NOTICE:
    Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-5 (SVC3) - O4-3 (SGD3)
    Always
    Below 1 Ω
    O4-9 (SIG3) - O4-3 (SGD3)
    Always
    Below 1 Ω

  1. Disconnect the service wires from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-5 (SVC3) - O4-3 (SGD3)
    Always
    1MΩ or Higher
    O4-9 (SIG3) - O4-3 (SGD3)
    Always
    1MΩ or Higher
    O4-5 (SVC3) - O4-9 (SIG3)
    Always
    1MΩ or Higher
    O4-3 (SGD3) - Body ground
    Always
    1MΩ or Higher
    O4-5 (SVC3) - Body ground
    Always
    1MΩ or Higher
    O4-9 (SIG3) - Body ground
    Always
    1MΩ or Higher

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O4-3 (SGD3) - Body ground
    Ignition switch ON
    Below 1 V
    O4-5 (SVC3) - Body ground
    Ignition switch ON
    Below 1 V
    O4-9 (SIG3) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


34.CHECK NO. 1 SEAT WIRE (OCCUPANT CLASSIFICATION SENSOR REAR RH CIRCUIT)
H100920E09
H100210E07
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the occupant classification ECU and the occupant classification sensor rear LH.

  1. Using service wires, connect O9-1 (SVC4) and O9-3 (SGD4), and connect O9-2 (SIG4) and O9-3 (SGD4) of connector C.

    NOTICE:
    Do not forcibly insert the service wires into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-6 (SVC4) - O4-4 (SGD4)
    Always
    Below 1 Ω
    O4-10 (SIG4) - O4-4 (SGD4)
    Always
    Below 1 Ω

  1. Disconnect the service wires from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-6 (SVC4) - O4-4 (SGD4)
    Always
    1MΩ or Higher
    O4-10 (SIG4) - O4-4 (SGD4)
    Always
    1MΩ or Higher
    O4-6 (SVC4) - O4-10 (SIG4)
    Always
    1MΩ or Higher
    O4-4 (SGD4) - Body ground
    Always
    1MΩ or Higher
    O4-6 (SVC4) - Body ground
    Always
    1MΩ or Higher
    O4-10 (SIG4) - Body ground
    Always
    1MΩ or Higher

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O4-4 (SGD4) - Body ground
    Ignition switch ON
    Below 1 V
    O4-6 (SVC4) - Body ground
    Ignition switch ON
    Below 1 V
    O4-10 (SIG4) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


35.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.


NEXT


36.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT


37.CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. The passenger airbag ON/OFF indicator (ON and OFF) comes on for approximately 4 seconds, then turns off for approximately 2 seconds.

  1. Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/OFF indicator indicates ON/OFF according to the condition listed below.

    Result:
    Double cab:

    Front Seat Passenger
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    ON
    OFF
    OFF
    Child seated / Child restrain system set
    OFF
    ON
    OFF
    Vacant
    OFF
    OFF
    OFF
    Except double cab:

    Front Seat Passenger
    Airbag Cut-Off Switch
    ON Indicator
    OFF Indicator
    SRS Warning Light
    Adult seated
    AUTO
    ON
    OFF
    OFF
    Adult seated
    OFF
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    AUTO
    OFF
    ON
    OFF
    Child seated / Child restrain system set
    OFF
    OFF
    ON
    OFF
    Vacant
    AUTO
    OFF
    OFF
    OFF
    Vacant
    OFF
    OFF
    ON
    OFF



OK
END
NG


38.REPLACE OCCUPANT DETECTION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).


NEXT


39.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.



NG
Go to step 41
OK


40.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



OK
END
NG


41.REPLACE FRONT SEAT WITH ADJUSTER FRAME ASSEMBLY RH
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat with adjuster frame assembly RH (Click here).


NEXT


42.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed on the tester.


NEXT


43.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END