Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Seat Belt Warning Light for Passenger Seat does not Flash

for Preparation Click here


WIRING DIAGRAM


B125017E01


B125017E02


INSPECTION PROCEDURE

HINT:
If there is an open in the ground circuit (center airbag sensor assembly), the center airbag sensor assembly outputs DTCs. Troubleshoot those DTCs by following the Supplemental Restraint System (Click here).

1.CONFIRM SEAT TYPE
  1. Confirm the seat type.
    Seat Type
    Proceed To
    Bench seat
    A
    Separate seat
    B



B
Go to step 9
A


2.CHECK SUPPLEMENTAL RESTRAINT SYSTEM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / SRS AIRBAG / DTC INFO

Result:
Result
Proceed to
No SRS DTCs are output
A
SRS DTCs are output
B



B
GO TO SUPPLEMENTAL RESTRAINT SYSTEM
A


3.CHECK OCCUPANT CLASSIFICATION SYSTEM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON position and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / OCCUPANT DETECT / DTC INFO

Result:
Result
Proceed to
No occupant classification system DTCs are output
A
Occupant classification system DTCs are output
B



B
GO TO OCCUPANT CLASSIFICATION SYSTEM
A


4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)


    I102255E01
  1. Disconnect the F24 front seat inner belt assembly (passenger side) connector.

  1. Measure the resistance.

    Standard Resistance:
    Terminal Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt fastened
    10 kΩ or higher
    1 - 2
    Seat belt unfastened
    Below 1 Ω

  1. Reconnect the front seat inner belt assembly (passenger side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)
OK


5.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - HAZARD WARNING SIGNAL SWITCH)


    I101316E02
  1. Disconnect the H7 hazard warning signal switch connector.

  1. Disconnect the A21 center airbag sensor assembly connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    H7-8 - A21-13
    Below 1 Ω
    H7-8 or A21-13 - Body ground
    10 kΩ or higher

  1. Reconnect the center airbag sensor assembly connector.

  1. Reconnect the hazard warning signal switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - OCCUPANT CLASSIFICATION ECU)


    I102251E01
  1. Disconnect the O10 occupant classification ECU connector.

  1. Disconnect the A23 center airbag sensor assembly connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A23-13 - O10-12
    Below 1 Ω
    A23-12 - O10-11
    Below 1 Ω
    A23-13 or O10-12 - Body ground
    10 kΩ or higher
    A23-12 or O10-11 - Body ground
    10 kΩ or higher

  1. Reconnect the center airbag sensor assembly connector.

  1. Reconnect the occupant classification ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (OCCUPANT CLASSIFICATION ECU - FRONT SEAT INNER BELT ASSEMBLY)


    I102252E01
  1. Disconnect the F24 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the O10 occupant classification ECU connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    O10-13 - F24-2
    Below 1 Ω
    O10-14 - F24-1
    Below 1 Ω
    O10-13 or F24-2 - Body ground
    10 kΩ or higher
    O10-14 or F24-1 - Body ground
    10 kΩ or higher

  1. Reconnect the occupant classification ECU connector.

  1. Reconnect the front seat inner belt assembly (passenger side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT HAZARD WARNING SIGNAL SWITCH
  1. Remove the hazard warning signal switch.

  1. Disconnect the H7 hazard warning signal switch connector.



    I102257E01
  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H7-3 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HAZARD WARNING SIGNAL SWITCH 

9.CHECK SUPPLEMENTAL RESTRAINT SYSTEM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / SRS AIRBAG / DTC INFO

Result:
Result
Proceed to
No SRS DTCs are output
A
SRS DTCs are output
B



B
GO TO SUPPLEMENTAL RESTRAINT SYSTEM
A


10.CHECK OCCUPANT CLASSIFICATION SYSTEM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON position and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / OCCUPANT DETECT / DTC INFO

Result:
Result
Proceed to
No occupant classification system DTCs are output
A
Occupant classification system DTCs are output
B



B
GO TO OCCUPANT CLASSIFICATION SYSTEM
A


11.INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)


    I102254E01
  1. Disconnect the F25 front seat inner belt assembly (passenger side) connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt fastened
    10 kΩ or higher
    1 - 2
    Seat belt unfastened
    Below 1 Ω

  1. Reconnect the front seat inner belt assembly (passenger side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)
OK


12.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - HAZARD WARNING SIGNAL SWITCH)


    I101316E01
  1. Disconnect the H7 hazard warning signal switch connector.

  1. Disconnect the A21 center airbag sensor assembly connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    H7-8 - A21-13
    Below 1 Ω
    H7-8 or A21-13 - Body ground
    10 kΩ or higher

  1. Reconnect the center airbag sensor assembly connector.

  1. Reconnect the hazard warning signal switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - OCCUPANT CLASSIFICATION ECU)


    I101317E01
  1. Disconnect the O5 occupant classification ECU connector.

  1. Disconnect the A23 center airbag sensor assembly connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A23-13 - O5-4
    Below 1 Ω
    A23-12 - O5-8
    Below 1 Ω
    A23-13 or O5-4 - Body ground
    10 kΩ or higher
    A23-12 or O5-8 - Body ground
    10 kΩ or higher

  1. Reconnect the center airbag sensor assembly connector.

  1. Reconnect the occupant classification ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (OCCUPANT CLASSIFICATION ECU - FRONT SEAT INNER BELT ASSEMBLY)


    I102253E01
  1. Disconnect the F25 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the O5 occupant classification ECU connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    O5-9 - F25-2
    Below 1 Ω
    O5-5 - F25-1
    Below 1 Ω
    O5-9 or F25-2 - Body ground
    10 kΩ or higher
    O5-9 or F25-1 - Body ground
    10 kΩ or higher

  1. Reconnect the occupant classification ECU connector.

  1. Reconnect the front seat inner belt assembly (passenger side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.INSPECT HAZARD WARNING SIGNAL SWITCH
  1. Remove the hazard warning signal switch.

  1. Disconnect the H7 hazard warning signal switch connector.



    I102257E01
  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H7-3 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HAZARD WARNING SIGNAL SWITCH