Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Power Windows do not Operate at All

for Preparation Click here


DESCRIPTION

If none of the door windows operate, there may be a failure in the supply of power to the power window regulator master switch assembly, or the power window regulator master switch itself may be malfunctioning.

WIRING DIAGRAM


B124994E05


INSPECTION PROCEDURE

1.INSPECT FUSE (D FR P/W, IG1 NO.2, ECU-B, AM1, J/B)
  1. Remove the D FR P/W and IG1 No.2 fuses from the driver side J/B.

  1. Remove the ECU-B, AM1 and J/B fuses from the engine room R/B.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the D FR P/W and IG1 No.2 fuses.

  1. Reinstall the ECU-B, AM1 and J/B fuses.



NG
REPLACE FUSE
OK


2.INSPECT RELAY (P/W)


    B060778E68
  1. Remove the P/W relay from the driver side J/B.

  1. Measure the resistance.

    Standard voltage:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)

  1. Reinstall the P/W relay.



NG
REPLACE RELAY
OK


3.CHECK HARNESS AND CONNECTOR (FOR POWER SOURCE OF DRIVER SIDE J/B ASSEMBLY)


    B087984E01
  1. Disconnect the 1A,1C, and 1H driver side J/B connectors.

  1. Measure the voltage and resistance.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1A-6 - Body ground
    Constant
    10 to 14 V
    1C-16 (ECU-B) - Body ground
    Constant
    10 to 14 V
    1A-4 (IG) - Body ground
    Ignition switch ON
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1H-18 (GND) - Body ground
    Constant
    Below 1 Ω

  1. Reconnect the driver side J/B connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BODY GROUND)
  1. Disconnect the P9 power window regulator master switch connector.



    B062895E08
    B087982E01
  1. Measure the voltage or resistance.

    Standard voltage:
    Double cab:
    Tester Connection
    Condition
    Specified Condition
    P9-7 (B) - Body ground
    Ignition switch ON
    10 to 14 V
    Access cab:
    Tester Connection
    Condition
    Specified Condition
    P9-9 (B) - Body ground
    Ignition switch ON
    10 to 14 V


    Standard resistance:
    Double cab:
    Tester Connection
    Condition
    Specified Condition
    P9-1 (E) - Body ground
    Constant
    Below 1 Ω
    Access cab:
    Tester Connection
    Condition
    Specified Condition
    P9-1 (E) - Body ground
    Constant
    Below 1 Ω

  1. Reconnect the power window regulator master switch connector.



OK
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
NG


5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE J/B - POWER WINDOW REGULATOR MASTER SWITCH)


    B087985E01
  1. Disconnect the 1H driver side J/B connectors.

  1. Disconnect the P9 power window regulator master switch connector.

  1. Measure the resistance.

    Standard resistance (Double cab):
    Tester Connection
    Specified Condition
    1H-1 - P9-7 (B)
    Below 1 Ω

    Standard resistance (Access cab):
    Tester Connection
    Specified Condition
    1H-1 - P9-9 (B)
    Below 1 Ω

  1. Reconnect the driver side J/B connector.



    B087986E01
  1. Reconnect the power window regulator master switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK