Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors cannot be Locked / Unlocked Simultaneously

for Preparation Click here


DESCRIPTION

The multiplex network body ECU activates the door lock motors with switch signals from the master switch, door control switch and driver/passenger side door key cylinder.

WIRING DIAGRAM


B124998E02


B125004E02


INSPECTION PROCEDURE

1.INSPECT ALL DOORS LOCK/UNLOCK OPERATION
All the doors can be locked/unlocked simultaneously using the following items:
  1. Door control switch on the master switch (switch operation)
  2. Door control switch on the front passenger side (switch operation)
  3. Door key cylinder linked with driver and passenger side door lock (key operation)
    If all the doors cannot be locked/unlocked simultaneously, proceed to the next step according to the malfunctioning part shown in the table below.

Result: 
Malfunctioning Part
Proceed to
Driver side doors
A
Passenger side doors
B
All items are malfunctioning
C


B
Go to step 3

C
Go to step 14
A


2.INSPECT DRIVER SIDE DOORS LOCK/UNLOCK OPERATION

Malfunctioning Part
Proceed to
Door control switch on master switch
A
Driver side door key cylinder
B
Door control switch on master switch and driver side door key cylinder
C


A
Go to step 4

B
Go to step 6

C
Go to step 9

3.INSPECT PASSENGER SIDE DOORS LOCK/UNLOCK OPERATION

Malfunctioning Part
Proceed to
Door control switch on passenger side switch
A
Passenger side door key cylinder
B
Door control switch on passenger side and passenger side door key cylinder
C


A
Go to step 16

B
Go to step 18

C
Go to step 21

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)


    B128473E01
  1. Remove the power window regulator master switch assembly.

  1. Measure the resistance of the door control switch.

    Standard (Double cab):
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 5 (L)
    Lock
    Below 1 Ω
    1 (E) - 5 (L)
    1 (E) - 8 (UL)
    OFF
    10 kΩ or higher
    1 (E) - 8 (UL)
    Unlock
    Below 1 Ω

    Standard (Access cab):
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 2 (L)
    Lock
    Below 1 Ω
    1 (E) - 2 (L)
    1 (E) - 5 (UL)
    OFF
    10 kΩ or higher
    1 (E) - 5 (UL)
    Unlock
    Below 1 Ω

  1. Reinstall the power window regulator master switch assembly.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH (SWITCH) - DRIVER SIDE J/B AND BODY GROUND)


    B128474E01
  1. Disconnect the P9 power window regulator master switch connector.

  1. Disconnect the 1I driver side J/B connector.

  1. Measure the resistance.

    Standard (Double cab):
    Tester Connection
    Specified Condition
    P9-5 (L) - 1I-18 (L1)
    Below 1 Ω
    P9-8 (UL) - 1I-14 (UL1)
    Below 1 Ω
    P9-1 (E) - Body ground
    Below 1 Ω
    P9-5 (L) or 1I-18 (L1) - Body ground
    10 kΩ or higher
    P9-8 (UL) or 1I-14 (UL1) - Body ground
    10 kΩ or higher

    Standard (Access cab):
    Tester Connection
    Specified Condition
    P9-2 (L) - 1I-18 (L1)
    Below 1 Ω
    P9-5 (UL) - 1I-14 (UL1)
    Below 1 Ω
    P9-1 (E) - Body ground
    Below 1 Ω
    P9-2 (L) or 1I-18 (L1) - Body ground
    10 kΩ or higher
    P9-5 (UL) or 1I-14 (UL1) - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the driver side J/B connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK 

6.INSPECT FRONT DOOR LOCK ASSEMBLY LH (DOOR LOCK MOTOR)


    B065427E16
  1. Apply battery voltage to the door lock and check operation of the door lock motor.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 4.

    OK:
    Terminal No
    Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH
OK


7.INSPECT FRONT DOOR LOCK ASSEMBLY LH (DOOR LOCK AND UNLOCK SWITCH AND POSITION SWITCH)


    B065428E06
  1. Measure the resistance of the door lock and unlock switch and position switch.

    Standard (Door lock and unlock switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    7 - 9
    Lock
    Below 1 Ω
    7 - 9, 7 - 10
    OFF
    10 kΩ or higher
    7 - 10
    Unlock
    Below 1 Ω

    Standard (Position switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    7 - 8
    Lock
    10 kΩ or higher
    7 - 8
    Unlock
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH
OK


8.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK LH - ECU, DRIVER SIDE J/B AND BODY GROUND)


    B088348E01
  1. Disconnect the D19 front door lock connector.

  1. Disconnect the B5 multiplex network body ECU connector.

  1. Disconnect the 1H and 1I driver side J/B connectors.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    D19-4 - 1H-24 (ACT+)
    Below 1 Ω
    D19-1 - B5-3 (ACTD)
    Below 1 Ω
    D19-9 - 1I-17 (L2)
    Below 1 Ω
    D19-10 - B5-23 (UL3)
    Below 1 Ω
    D19-8 - B5-20 (LSWD)
    Below 1 Ω
    D19-7 - Body ground
    Below 1 Ω
    D19-4 or 1H-24 (ACT+) - Body ground
    10 kΩ or higher
    D19-1 or B5-3 (ACTD) - Body ground
    10 kΩ or higher
    D19-9 or 1I-17 (L2) - Body ground
    10 kΩ or higher
    D19-10 or B5-23 (UL3) - Body ground
    10 kΩ or higher
    D19-8 or B5-20 (LSWD) - Body ground
    10 kΩ or higher

  1. Reconnect the front door lock connector.

  1. Reconnect the multiplex network body ECU connector.

  1. Reconnect the driver side J/B connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK (MULTIPLEX NETWORK BODY ECU) 

9.INSPECT FRONT DOOR LOCK ASSEMBLY LH (DOOR LOCK MOTOR)


    B065427E16
  1. Apply battery voltage to the door lock and check operation of the door lock motor.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 4

    OK:
    Terminal No
    Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH
OK


10.INSPECT FRONT DOOR LOCK ASSEMBLY LH (DOOR LOCK AND UNLOCK SWITCH AND POSITION SWITCH)


    B065428E06
  1. Measure the resistance of the door lock and unlock switch and position switch.

    Standard (Door lock and unlock switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    7 - 9
    Lock
    Below 1 Ω
    7 - 9
    7 - 10
    OFF
    10 kΩ or higher
    7 - 10
    Unlock
    Below 1 Ω

    Standard (Position switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    7 - 8
    Lock
    10 kΩ or higher
    7 - 8
    Unlock
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY LH
OK


11.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK LH - ECU, DRIVER SIDE J/B AND BODY GROUND)


    B088348E01
  1. Disconnect the D19 front door lock connector.

  1. Disconnect the B5 multiplex network body ECU connector.

  1. Disconnect the 1H and 1I driver side J/B connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard:
    Tester Connection
    Specified Condition
    D19-4 - 1H-24 (ACT+)
    Below 1 Ω
    D19-1 - B5-3 (ACTD)
    Below 1 Ω
    D19-9 - 1I-17 (L2)
    Below 1 Ω
    D19-10 - B5-23 (UL3)
    Below 1 Ω
    D19-8 - B5-20 (LSWD)
    Below 1 Ω
    D19-7 - Body ground
    Below 1 Ω
    D19-4 or 1H-24 (ACT+) - Body ground
    10 kΩ or higher
    D19-1 or B5-3 (ACTD) - Body ground
    10 kΩ or higher
    D19-9 or 1I-17 (L2) - Body ground
    10 kΩ or higher
    D19-10 or B5-23 (UL3) - Body ground
    10 kΩ or higher
    D19-8 or B5-20 (LSWD) - Body ground
    10 kΩ or higher

  1. Reconnect the front door lock connector.

  1. Reconnect the multiplex network body ECU connector.

  1. Reconnect the driver side J/B connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)


    B128473E01
  1. Remove the power window regulator master switch assembly.

  1. Measure the resistance of the door control switch.

    Standard (Double cab):
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 5 (L)
    Lock
    Below 1 Ω
    1 (E) - 5 (L)
    1 (E) - 8 (UL)
    OFF
    10 kΩ or higher
    1 (E) - 8 (UL)
    Unlock
    Below 1 Ω

    Standard (Access cab):
    Tester Connection
    Switch Condition
    Specified Condition
    1 (E) - 2 (L)
    Lock
    Below 1 Ω
    1 (E) - 2 (L)
    1 (E) - 5 (UL)
    OFF
    10 kΩ or higher
    1 (E) - 5 (UL)
    Unlock
    Below 1 Ω

  1. Reinstall the power window regulator master switch assembly.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


13.CHECK HARNESS AND CONNECTOR (MASTER SWITCH (SWITCH) - DRIVER SIDE J/B AND BODY GROUND)


    B128474E01
  1. Disconnect the P9 power window regulator master switch connector.

  1. Disconnect the 1I driver side J/B connector.

  1. Measure the resistance.

    Standard (Double cab):
    Tester Connection
    Specified Condition
    P9-5 (L) - 1I-18 (L1)
    Below 1 Ω
    P9-8 (UL) - 1I-14 (UL1)
    Below 1 Ω
    P9-1 (E) - Body ground
    Below 1 Ω
    P9-5 (L) or 1I-18 (L1) - Body ground
    10 kΩ or higher
    P9-8 (UL) or 1I-14 (UL1) - Body ground
    10 kΩ or higher

    Standard (Access cab):
    Tester Connection
    Specified Condition
    P9-2 (L) - 1I-18 (L1)
    Below 1 Ω
    P9-5 (UL) - 1I-14 (UL1)
    Below 1 Ω
    P9-1 (E) - Body ground
    Below 1 Ω
    P9-2 (L) or 1I-18 (L1) - Body ground
    10 kΩ or higher
    P9-5 (UL) or 1I-14 (UL1) - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the driver side J/B connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK 

14.INSPECT FUSE (DR LCK, J/B, ECU-B, ALT)
  1. Remove the DR LCK fuse from the driver side J/B.

  1. Remove the J/B, ECU-B and ALT fuses from the engine room R/B.

  1. Measure the resistance of the fuse.

    Standard:
    Below 1 Ω

  1. Reinstall the DR LCK fuse.

  1. Reinstall the J/B, ECU-B and ALT fuses.



NG
REPLACE FUSE
OK


15.CHECK HARNESS AND CONNECTOR (DRIVER SIDE J/B ASSEMBLY - BODY GROUND)
  1. Disconnect the 1A, 1C, and 1H driver side J/B connectors.



  1. Measure the voltage and resistance.


    B125003E01


    Standard:

    Tester Connection
    Specified Condition
    1A-6 (ALTB) - Body ground
    10 to 14 V
    1H-18 (GND) - Body ground
    Below 1 Ω
    1C-16 (ECUB) - Body ground
    10 to 14 V

  1. Reconnect the driver side J/B connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK 

16.INSPECT DOOR CONTROL SWITCH ASSEMBLY


    B071970E15
  1. Remove the door control switch (passenger side).

  1. Measure the resistance of the door control switch.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (E) - 6 (L)
    Lock
    Below 1 Ω
    3 (E) - 5 (UL)
    3 (E) - 6 (L)
    OFF
    10 kΩ or higher
    3 (E) - 5 (UL)
    Unlock
    Below 1 Ω

  1. Reinstall the door control switch.



NG
REPLACE DOOR CONTROL SWITCH ASSEMBLY
OK


17.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH - DRIVER SIDE J/B AND BODY GROUND)


    B088347E01
  1. Disconnect the D23 door control switch connector.

  1. Disconnect the 1I driver side J/B connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    D23-6 (L) - 1I-7 (L1)
    Below 1 Ω
    D23-5 (UL) - 1I-3 (UL1)
    Below 1 Ω
    D23-3 (E) - Body ground
    Below 1 Ω
    D23-6 (L) or 1I-7 (L1) - Body ground
    10 kΩ or higher
    D23-5 (UL) or 1I-3 (UL1) - Body ground
    10 kΩ or higher

  1. Reconnect the door control switch connector.

  1. Reconnect the driver side J/B connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK 

18.INSPECT FRONT DOOR LOCK ASSEMBLY RH (DOOR LOCK MOTOR)


    B065429E16
  1. Apply battery voltage to the door lock and check operation of the door lock motor.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 4.

    OK:
    Terminal No
    Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH
OK


19.INSPECT FRONT DOOR LOWER FRAME BRACKET GARNISH RH (DOOR LOCK AND UNLOCK SWITCH AND POSITION SWITCH)


    B065430E14
  1. Measure the resistance of the door lock and unlock switch and position switch.

    Standard (Door lock and unlock switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    6 -8
    Lock
    Below 1 Ω
    5 - 8, 6 - 8
    OFF
    10 kΩ or higher
    5 - 8
    Unlock
    Below 1 Ω

    Standard (Position switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    7 - 8
    Lock
    10 kΩ or higher
    7 - 8
    Unlock
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH
OK


20.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK RH - ECU, DRIVER SIDE J/B AND BODY GROUND)


    B088348E02
  1. Disconnect the D20 front door lock connector.

  1. Disconnect the B5 multiplex network body ECU connector.

  1. Disconnect the 1H and 1I driver side J/B connectors.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    D20-4 - 1H-23 (ACT+)
    Below 1 Ω
    D20-1 - 1H-5 (ACT-)
    Below 1 Ω
    D20-6 - 1I-4 (L2)
    Below 1 Ω
    D20-5 - 1I-19 (UL2)
    Below 1 Ω
    D20-7 - B5-11 (LSWP)
    Below 1 Ω
    D20-8 - Body ground
    Below 1 Ω
    D20-4 or 1H-23 (ACT+) - Body ground
    10 kΩ or higher
    D20-1 or 1H-5 (ACT-) - Body ground
    10 kΩ or higher
    D20-6 or 1I-4 (L2) - Body ground
    10 kΩ or higher
    D20-5 or 1I-19 (UL2) - Body ground
    10 kΩ or higher
    D20-7 or B5-11 (LSWP) - Body ground
    10 kΩ or higher

  1. Reconnect the front door lock connector.

  1. Reconnect the multiplex network body ECU connector.

  1. Reconnect the driver side J/B connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK (MULTIPLEX NETWORK BODY ECU) 

21.INSPECT FRONT DOOR LOCK ASSEMBLY RH (DOOR LOCK MOTOR)


    B065429E16
  1. Apply battery voltage to the door lock and check operation of the door lock motor.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 4.

    OK:
    Terminal No
    Specified Condition
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH
OK


22.INSPECT FRONT DOOR LOCK ASSEMBLY RH (DOOR LOCK AND UNLOCK SWITCH AND POSITION SWITCH)


    B065430E14
  1. Measure the resistance of the door lock and unlock switch and position switch.

    Standard (Door lock and unlock switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    6 -8
    Lock
    Below 1 Ω
    5 - 8, 6 - 8
    OFF
    10 kΩ or higher
    5 - 8
    Unlock
    Below 1 Ω

    Standard (Position switch):
    Tester Connection
    Door Lock Condition
    Specified Condition
    7 - 8
    Lock
    10 kΩ or higher
    7 - 8
    Unlock
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH
OK


23.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK RH - ECU, DRIVER SIDE J/B AND BODY GROUND)


    B088348E03
  1. Disconnect the D20 front door lock connector.

  1. Disconnect the B5 multiplex network body ECU connector.

  1. Disconnect the 1H and 1I driver side J/B connectors.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    D20-4 - 1H-23 (ACT+)
    Below 1 Ω
    D20-1 - 1H-5 (ACT-)
    Below 1 Ω
    D20-6 - 1I-4 (L2)
    Below 1 Ω
    D20-5 - 1I-19 (UL2)
    Below 1 Ω
    D20-7 - B5-11 (LSWP)
    Below 1 Ω
    D20-8 - Body ground
    Below 1 Ω
    D20-4 or 1H-23 (ACT+) - Body ground
    10 kΩ or higher
    D20-1 or 1H-5 (ACT-) - Body ground
    10 kΩ or higher
    D20-6 or 1I-4 (L2) - Body ground
    10 kΩ or higher
    D20-5 or 1I-19 (UL2) - Body ground
    10 kΩ or higher
    D20-7 or B5-11 (LSWP) - Body ground
    10 kΩ or higher

  1. Reconnect the front door lock connector.

  1. Reconnect the multiplex network body ECU connector.

  1. Reconnect the driver side J/B connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


24.INSPECT DOOR CONTROL SWITCH ASSEMBLY


    B071970E15
  1. Remove the door control switch (passenger side).

  1. Measure the resistance of the door control switch.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (E) - 6 (L)
    Lock
    Below 1 Ω
    3 (E) - 5 (UL)
    3 (E) - 6 (L)
    OFF
    10 kΩ or higher
    3 (E) - 5 (UL)
    Unlock
    Below 1 Ω

  1. Reinstall the door control switch.



NG
REPLACE DOOR CONTROL SWITCH ASSEMBLY
OK


25.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH - DRIVER SIDE J/B AND BODY GROUND)


    B088347E01
  1. Disconnect the D23 door control switch connector.

  1. Disconnect the 1I driver side J/B connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Specified Condition
    D23-6 (L) - 1I-7 (L1)
    Below 1 Ω
    D23-5 (UL) - 1I-3 (UL1)
    Below 1 Ω
    D23-3 (E) - Body ground
    Below 1 Ω
    D23-6 (L) or 1I-7 (L1) - Body ground
    10 kΩ or higher
    D23-5 (UL) or 1I-3 (UL1) - Body ground
    10 kΩ or higher

  1. Reconnect the door control switch connector.

  1. Reconnect the driver side J/B connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVER SIDE JUNCTION BLOCK