Home › BODY › SEAT › REAR SEAT ASSEMBLY (for RH Side)

REAR SEAT ASSEMBLY (for RH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp surface on the rear seat back frame could cause injuries to your hands.



1. INSTALL REAR SEAT BACK COVER


    B113844E02
  1. Using hog ring pliers, install the rear seat back cover with new hog rings.

    NOTICE:
    1. Do not contaminate or scratch the rear seat back cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.



2. INSTALL REAR SEAT LOCK HANDLE


    B087232E01
  1. Install the rear seat lock handle with the screw.



3. INSTALL REAR SEAT BACK LOCK ASSEMBLY


    B087231E01
  1. Install the rear seat back lock with the 2 bolts.

    Torque:
    30 N*m{ 305 kgf*cm , 22 ft.*lbf }



4. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    B087235E01
  1. Align the retractor with the positioning claws of the rear seat back frame and install the retractor with the bolt.

    Torque:
    44 N*m{ 450 kgf*cm , 33 ft.*lbf }

  1. Insert the belt through the hole into the rear seat back frame.



5. INSTALL REAR SEAT BACK FRAME SUB-ASSEMBLY


    B121732E01
  1. Install the rear seat back spring into the rear seat back pad.

  1. Using hog ring pliers, install new hog rings.



6. INSTALL REAR SEAT SHOULDER BELT COVER


    B087236E01
  1. Engage the 4 claws and install the rear seat shoulder belt cover.



7. INSTALL REAR SEAT HEADREST SUPPORT


B087227E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the front seat headrest support.



8. INSTALL REAR SEAT BACK BOARD SUB-ASSEMBLY


    B087225E02
  1. Disengage the lock button of the rear seat headrest support and install the rear seat headrest center.



9. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


    B087224E02
  1. Disengage the lock button of the rear seat headrest support and install the rear center seat headrest.



10. INSTALL REAR SEAT HEADREST ASSEMBLY


    B087226E01
  1. Engage the 5 claws and install the rear seat back board.

  1. Tighten the 3 screws.



11. INSTALL REAR SEAT CUSHION COVER


    B113845E02
  1. Using hog ring pliers, install the rear seat cushion cover with new hog rings.

    NOTICE:
    1. Do not contaminate or scratch the rear seat back cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.



12. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY


    B113846E02
  1. Engage the hook and install the rear seat cushion frame.

  1. Install a new hog ring.



13. INSTALL REAR SEAT CUSHION HINGE SUB-ASSEMBLY


B087237E01

HINT:
Follow the same procedures as for the opposite side.

  1. Install the rear seat cushion hinge with the bolt.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }



14. INSTALL REAR SEAT HEADREST HOLDER


B088237E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the rear seat headrest holder.



15. INSTALL REAR SEAT CUSHION BAND


    B087220E01
  1. Install the rear seat cushion band with the screw.