Home › BODY › EXTERIOR › FRONT BUMPER

FRONT BUMPER > INSTALLATION

for Preparation Click here



1. INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY LH


    B087551E01
  1. Install the front bumper extension with the 3 nuts.

    Torque:
    58 N*m{ 590 kgf*cm , 43 ft.*lbf }



2. INSTALL FRONT BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Follow the same procedures as for the front bumper extension LH.



3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B087550E01
  1. Install the front bumper reinforcement with the 6 nuts.

    Torque:
    58 N*m{ 590 kgf*cm , 43 ft.*lbf }



4. INSTALL FRONT BUMPER ARM MOUNTING BRACKET LH


    B087549E01
  1. Install the front bumper arm mounting bracket with the 2 bolts.

    Torque:
    13 N*m{ 135 kgf*cm , 10 ft.*lbf }



5. INSTALL FRONT BUMPER ARM MOUNTING BRACKET RH

HINT:
Follow the same procedures as for the front bumper arm mounting bracket LH.



6. INSTALL FRONT BUMPER REINFORCEMENT EXTENSION LH


    B087548E01
  1. Install the front bumper reinforcement extension with the 2 nuts.

    Torque:
    13 N*m{ 135 kgf*cm , 10 ft.*lbf }



7. INSTALL FRONT BUMPER REINFORCEMENT EXTENSION RH

HINT:
Follow the same procedures as for the front bumper reinforcement extension.



8. INSTALL FRONT BUMPER UPPER CENTER RETAINER


    B087547E01
  1. Install the front bumper upper center retainer with the 4 nuts.

    Torque:
    13 N*m{ 135 kgf*cm , 10 ft.*lbf }



9. INSTALL HEADLIGHT ASSEMBLY LH
  1. Connect the 3 connectors.



    E076046E02
  1. Install the LH headlight assembly with the bolt and 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }



10. INSTALL HEADLIGHT ASSEMBLY RH

HINT:
Follow the same procedures as for the headlight LH.



11. INSTALL FRONT BUMPER FILLER LH


    B087568E01
  1. Engage the 2 claws and install the front bumper filler.

  1. Install the clip.



12. INSTALL FRONT BUMPER FILLER RH

HINT:
Follow the same procedures as for the front bumper filler LH.



13. INSTALL FRONT BUMPER SIDE SUPPORT


B087567E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the claw and install the front bumper side support.

  1. Tighten the screw.



14. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)


    B087571E01
  1. Engage the 2 claws and install the front bumper hole cover.



15. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Follow the same procedures as for the front bumper hole cover LH.



16. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    B087572E01
  1. Engage the 2 claws and install the fog light.



17. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Follow the same procedures as for the fog light LH.



18. INSTALL FRONT SPOILER CENTER COVER (for X-Runner)


    B087678E01
  1. Engage the 7 claws and install the front spoiler center cover.

  1. Install the 6 retainers.



19. INSTALL FRONT BUMPER EXTENSION LH


    B087577E01
  1. for 4WD and Pre Runner:

    1. Install the front bumper extension with the 5 retainers.



    B087576E01
  1. for X-Runner:

    1. Install the front bumper extension with the 4 retainers.



20. INSTALL FRONT BUMPER EXTENSION RH

HINT:
Follow the same procedures as for the front bumper extension LH.



21. INSTALL FRONT SPOILER COVER LH (for X-Runner)


    B087573E01
  1. Install the front spoiler cover with the 6 retainers.

  1. Install the 3 clips.



22. INSTALL FRONT SPOILER COVER RH (for X-Runner)


    B087574E01
  1. Install the front spoiler cover with the 6 retainers.

  1. Install the clip.



23. INSTALL FRONT BUMPER COVER


    B087570E01
  1. Install the 6 clips.



    B087566E01
  1. Engage the 2 claws and install the front bumper cover.

  1. Connect the 2 fog lamp connectors (w/ fog lamp).



    B087565E03
  1. Install the 9 clips.

  1. Tighten the 6 screws.



24. INSTALL RADIATOR GRILLE


    B087564E01
  1. Engage the 2 clips and install the radiator grille.

  1. Install the 2 clips.

  1. Tighten the 2 screws.



25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



26. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation to the body around the headlights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools, and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (68 kg, 150 lb) in the driver side seat.



27. PREPARE FOR HEADLIGHT AIMING (for Using a Tester)
  1. Prepare the vehicle for headlight aim check.

  1. Perform adjustment in accordance with the headlight tester instructions.



28. PREPARE FOR HEADLIGHT AIMING (for Using a Screen)
  1. Prepare the vehicle according to the following conditions:

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 7.62 m (25 ft) distance between the center of the headlight bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

    NOTICE:
    A distance of 7.62 m (25 ft) between the vehicle (center of the headlight bulb) and the wall is necessary for proper aim adjustment. If unavailable to secure a distance of 7.62 m (25 ft), secure a distance of exactly 3 m (9.84 ft) to check and adjust the headlight aim. (Since the target zone will change with the distance, follow the instructions shown in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of screen (V line).



  1. Set the screen as shown in the illustration.


    E076099E01

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    I033423E08
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

    HINT:
    1. The base lines differ for "low-beam inspection" and "high-beam inspection".
    2. Follow the same procedures as for "high-beam inspection".
    3. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the manufacturer name marked on the headlight as the center mark.


    1. H Line (Headlight height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
      Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).



29. INSPECT HEADLIGHT AIMING
  1. Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight not being inspected from affecting headlight aiming inspection.

    NOTICE:
    Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, and may easily melt or be damaged due to heat.

  1. Start the engine.

    NOTICE:
    Engine rpm must be 1,500 or more.



  1. Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    E113067E01

    HINT:
    1. Alignment distance is 7.62 m (25 ft):
      The cutoff line is 101 mm (3.97 in.) above and below the H line as well as to the left and right of the V line with low-beam (SAEJ599).
    2. Alignment distance is 3 m (9.84 ft):
      The cutoff line is 40 mm (1.57 in.) above and below the H line as well as to the left and right of the V line with low-beam (SAEJ599).
    3. Alignment distance is 7.62 m (25 ft):
      The cutoff line is 101 mm (3.97 in.) above and below the H line as well as to the left and right of the V line with high-beam (SAEJ599).
    4. Alignment distance is 3 m (9.84 ft):
      The cutoff line is 40 mm (1.57 in.) above and below the H line as well as to the left and right of the V line with high-beam (SAEJ599).
    5. Alignment distance is 7.62 m (25 ft):
      The cutoff line is 0 mm (0 in.) below the H line with low-beam.
    6. Alignment distance is 3 m (9.84 ft):
      The cutoff line is 0 mm (0 in.) below the H line with low-beam.



30. ADJUST HEADLIGHT AIMING


    E076100E01
  1. Adjust the aim vertically:
    Adjust the headlight aim into the specified range by turning aiming screw A with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

  1. Perform low-beam aim adjustment.

    HINT:
    The headlight aim moves up when turning the aiming screw clockwise, and moves down when turning the aiming screw counterclockwise.



    E076101E01
  1. Adjust the aim horizontally:
    Adjust the headlight aim into the specified range by turning aiming screw B with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.



31. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    HINT:
    1. Ensure that there is no damage or deformation to the body around the fog lights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools, and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (68 kg, 150 lb) in the driver side seat.



32. PREPARE FOR FOG LIGHT AIMING


E076102E01
  1. Prepare the vehicle according to the following conditions:

    HINT:
    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 7.62 m (25 ft) distance between the center of the fog light bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

    NOTICE:
    A distance of 7.62 m (25 ft) between the vehicle (center of the fog light bulb) and the wall is necessary for proper aim adjustment. If unavailable to secure a distance of 7.62 m (25 ft), secure a distance of exactly 3 m (9.84 ft) to check and adjust the fog light aim. (Since the target zone will change with the distance, follow the instructions shown in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of screen (V line).



  1. Set the screen as shown in the illustration.


    E076103E01

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    I033423E08
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.



33. INSPECT FOG LIGHT AIMING
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light not being inspected from affecting fog light aiming inspection.

  1. Start the engine.

    NOTICE:
    Engine rpm must be 1,500 or more.



  1. Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    I041221E03



34. ADJUST FOG LIGHT AIMING


E076104E01
  1. Adjust the fog light aim into the specified range by turning the aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, Loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.