Home › BODY › EXTERIOR › REAR BUMPER

REAR BUMPER > INSTALLATION

for Preparation Click here



1. INSTALL LICENSE PLATE LIGHT ASSEMBLY


B087531E01

HINT:
Follow the same procedures as for the opposite side.

  1. Install the nut into the rear bumper bar.



    B087530E01
  1. Install the bumper moulding mounting plate onto the license plate light.



    B087529E01
  1. Engage the claw and install the license plate light.

  1. Install the screw.



2. INSTALL REAR BUMPER BAR CORNER REINFORCEMENT LH


    B087528E01
  1. Install the rear bumper bar corner reinforcement with 4 bolts.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



3. INSTALL REAR BUMPER BAR CORNER REINFORCEMENT RH

HINT:
Follow the same procedures as for the rear bumper bar corner reinforcement LH.



4. INSTALL REAR BUMPER PLATE LH


    B087519E01
  1. Engage the claw and install the bumper plate.

  1. Install the 2 nuts.

    Torque:
    7.0 N*m{ 70 kgf*cm , 62 in.*lbf }



5. INSTALL REAR BUMPER PLATE RH

HINT:
Follow the same procedures as for the rear bumper plate LH.



6. INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH (w/o Towing Hitch)


    B087526E01
  1. Install the rear bumper arm with the 2 bolts..

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



7. INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH (w/o Towing Hitch)

HINT:
Follow the same procedures as for the rear bumper arm LH.



8. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Towing Hitch)


    B087524E01
  1. Install the rear bumper bar reinforcement with the 10 bolts.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



9. INSTALL NO. 3 FRAME WIRE (w/ Towing Hitch)


    B087527E01
  1. Install the No. 3 frame wire with the 2 bolts.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Install the 2 wire harness clamps.



10. INSTALL RECEIVER HITCH BRACKET SUB-ASSEMBLY (w/ Towing Hitch)


    B087525E01
  1. Install the receiver hitch bracket with the 10 bolts.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Connect the 2 license light connectors.



11. INSTALL REAR BUMPER PLATE


    B087518E01
  1. Engage the 14 claws and install the rear bumper No. 1 plate.

  1. Install the 3 clips.



12. INSTALL REAR BUMPER COVER


    B087523E01
  1. Install the 2 nuts into the rear bumper bar.



    B087522E01
  1. Engage the 4 claws and install the rear bumper pad center.

  1. Tighten the 4 bolts.



    B088213E01
  1. Engage the 2 claws and install the rear bumper cover lower.

    HINT:
    Follow the same procedures as for the opposite side.



    B087532E01
  1. w/ Towing Hitch:

    1. Install the hitch ball.

    2. Tighten the 2 bolts.



    3. B087520E01
    4. Engage the 3 claws and remove the receiver hitch cap.

      HINT:
      Follow the same procedures as for the opposite side.



13. INSTALL REAR BUMPER SPOILER LH (for X-Runner)


    B087649E01
  1. Engage the 4 clips and install the rear bumper spoiler.

  1. Tighten the screw.

  1. Install the 2 clips.



14. INSTALL REAR BUMPER SPOILER RH (for X-Runner)

HINT:
Follow the same procedures as for the rear bumper spoiler LH.



15. INSTALL REAR BUMPER BAR


    B088212E02
  1. w/ Towing hitch:

    1. Engage the 2 pins and remove the rear bumper bar.

    2. Tighten the 8 bolts.

      Torque:
      90 N*m{ 920 kgf*cm , 67 ft.*lbf }

    3. Connect the 2 No. 3 wire frame connectors.



    B088211E02
  1. w/o Towing hitch:

    1. Engage the 2 pins and install the rear bumper bar.

    2. Tighten the 6 bolts.

      Torque:
      90 N*m{ 920 kgf*cm , 67 ft.*lbf }

    3. Connect the 2 license lamp connectors.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }