Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > TERMINALS OF ECU

for Preparation Click here



INSPECT AIR CONDITIONER AMPLIFIER ASSEMBLY


  1. Disconnect the connector from the air conditioner amplifier assembly and inspect the connector on the wire harness side, as shown in the table below.


    I036518E01


    Symbols (Terminals No.)
    Wiring Colors
    Terminal Descriptions
    Conditions
    STD Voltages
    IG+ (A14-12) - GND (A14-1)
    P - W-B
    Power source (IG)
    Ignition switch: OFF → ON
    Below 1.0 → 10 to 14 V
    +B (A14-24) - GND (A14-1)
    P - W-B
    Power source (Back-up)
    Always
    10 to 14 V
    GND (A14-1) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1.0 Ω
    If the results are not as specified, inspect the circuits connected to the other parts.



  2. Connect the connector to the air conditioning amplifier assembly and inspect the wire harness side connector from the back side, as shown in the table below.


    I036517E01


    Symbols (Terminals No.)
    Wiring Colors
    Terminal Descriptions
    Conditions
    STD Voltages
    DEF (A14-2) - GND (A14-1)
    LG - W-B
    Mode switch signal
    Ignition switch: ON
    Mode select switch:
    Except DEF → DEF
    1.0 to 14 → Below 1.0 V
    LOCK (A14-6) - SG (A14-3)
    R-W - W
    Magnet clutch signal
    Start engine
    Operate A/C system
    Magnet clutch: ON
    Pulse generation (See waveform 1)
    ACI (A14-9) - GND (A14-1)
    G-W - W-B
    Idle up request signal
    Engine idling
    Operate A/C system
    Magnet clutch: OFF → ON
    10 to 14 → Below 1.0 V
    FRS (A14-10) - GND (A14-1)
    V-W - W-B
    Recirculation/Fresh switch signal
    Ignition switch: ON
    Recirculation/Fresh switch:
    RECIRCULATION → FRESH
    Below 1.0 → 10 to 14 V
    REC (A14-11) - GND (A14-1)
    P-B - W-B
    Recirculation/Fresh switch signal
    Ignition switch: ON
    Recirculation/Fresh switch:
    FRESH → RECIRCULATION
    Below 1.0 → 10 to 14 V
    MGC (A14-21) - GND (A14-1)
    G - W-B
    Magnet clutch relay signal
    Engine idling
    Operate A/C system
    Magnet clutch: OFF → ON
    10 to 14 → Below 1.0 V
    PRS (A14-5) - GND (A14-1)
    O - W-B
    A/C pressure sensor signal
    Start engine
    Operate A/C system
    Refrigerant pressure: Abnormal (More than 3,030 kPa (31.0 kgf/cm2, 440 psi))
    4.7 V or higher
    PRS (A14-5) - GND (A14-1)
    O - W-B
    A/C pressure sensor signal
    Start engine
    Operate A/C system
    Refrigerant pressure: Abnormal (Less than 186 kPa (1.9 kgf/cm2, 27 psi))
    Below 0.7 V
    PRS (A14-5) - GND (A14-11)
    O - W-B
    A/C pressure sensor signal
    Start engine
    Operate A/C system
    Refrigerant pressure: Normal (Less than 3,030 kPa (31.0 kgf/cm2, 440 psi)) and more than 186 kPa (1.9 kgf/cm2, 27 psi))
    0.7 to 4.7 V
    TE (A14-4) - GND (A14-1)
    B - W-B
    A/C evaporator temperature sensor signal
    Ignition switch: ON
    Evaporator temperature:
    0 → 15°C (32 → 59°F)
    2.0 to 2.4 → 1.4 to 1.8 V
    BLRH (A14-23) - GND (A14-1)
    G-Y - W-B
    Blower switch signal
    Ignition switch: ON
    Blower switch: ON
    OFF → ON (LO, M1, M2, H1)
    0 → 10 to 14 V
    ACID (A14-15) - GND (A14-1)
    Y - W-B
    A/C switch LED signal
    Ignition switch: ON
    Blower switch: ON
    A/C switch: OFF → ON
    10 to 14 → Below 3.0 V
    RDEF (A14-16) - GND (A14-1)
    L-W - W-B
    REC switch LED signal
    Ignition switch: ON
    Blower switch: ON
    REC switch: OFF → ON
    10 to 14 → Below 1.0 V
    MR/F (A14-17) - GND (A14-1)
    G-B - W-B
    REC switch operation signal
    Ignition switch: ON
    REC switch: OFF → ON
    4 to 5 → Below 1.0 V
    A/C (A14-18) - GND (A14-1)
    GR - W-B
    A/C switch operation signal
    Ignition switch: ON
    A/C switch: OFF → ON
    4 to 5 → Below 1.0 V
    GND (A14-1) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1.0 Ω
    SG (A14-3) - Body ground
    W - Body ground
    Ground for A/C evaporator temperature sensor
    Always
    Below 1.0 Ω
    IG (A14-12) - Body ground
    P - Body ground
    Power source (IG)
    Ignition switch: OFF → ON
    Below 1.0 → 10 to 14 V
    +B (A14-24) - Body ground
    R - Body ground
    Power source (Back-up)
    Always
    10 to 14 V
    If the results are not as specified, replace the air conditioning amplifier assembly with a new one. If the results are still not as specified after replacing the air conditioning control assembly, inspect the circuits connected to other parts.



      I045420E01
    1. WAVEFORM 1:
      Magnet clutch signal
      ECM Terminal Names
      Between LOCK and SG
      Tester Ranges
      0.2 V/DIV, 10 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.


Inspect ECM (2TR-FE)


  1. Connect the connector to the ECM and inspect the wire harness side connector from the back side, as shown in the table below.


    A066714E08


    Symbols (Terminals No.)
    Wiring Colors
    Terminal Descriptions
    Conditions
    STD Voltages
    ACT (E7-25) - E1 (E4-3)
    L - BR
    Magnet clutch ON
    Permit signal
    Start engine
    Operate A/C system
    Accelerator pedal:
    released → depressed
    10 to 14 → Below 1.0 V
    THWO (E7-14) - E2 (E4-28)
    GR-B - BR
    Engine coolant temperature sensor signal
    Ignition switch: ON
    Pulse generation
    (See waveform 1)
    TACH (E7-1) - E1 (E4-3)
    B-W - BR
    Engine speed signal
    Engine idling
    Pulse generation
    (See waveform 2)



      E050693E04
    1. WAVEFORM 1:
      Engine coolant temperature sensor signal
      ECM Terminal Names
      Between THWO and E2
      Tester Ranges
      5 V/DIV, 0.1 sec./DIV
      Conditions
      Ignition switch ON
      A changes in accordance with the engine coolant temperature.
      Coolant Temperature
      Below 30°
      Approx. 75°C
      Above 90°F
      A
      Approx. 16 ms
      Approx. 204 ms
      Approx. 262 ms



    2. A093225E06
    3. WAVEFORM 2:
      Engine speed signal
      ECM Terminal Names
      Between TACH and E1
      Tester Ranges
      5 V/DIV, 10 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.


INSPECT ECM (1GR-FE)


  1. Connect the connector to the ECM and inspect the wire harness side connector from the back side, as shown in the table below.


    G035613E03


    Symbols (Terminals No.)
    Wiring Colors
    Terminal Descriptions
    Conditions
    STD Voltages
    ACT (E7-25) - E1 (E6-1)
    L - BR
    Magnet clutch ON
    permit signal
    Start engine
    Operate A/C system
    Accelerator pedal:
    released → depressed
    10 to 14 → Below 1.0 V
    THWO (E7-14) - E2 (E4-28)
    GR-B - BR
    Engine coolant temperature sensor signal
    Ignition switch: ON
    Pulse generation
    (See waveform 1)
    TACH (E7-1) - E1 (E6-1)
    B-W - BR
    Engine speed signal
    Engine idling
    Pulse generation
    (See waveform 2)



      E050693E04
    1. WAVEFORM 1:
      Engine coolant temperature sensor signal
      ECM Terminal Names
      Between THWO and E2
      Tester Ranges
      5 V/DIV, 0.1 sec./DIV
      Conditions
      Ignition switch ON
      A changes in accordance with the engine coolant temperature.
      Coolant Temperature
      Below 30°
      Approx. 75°
      Above 90°
      A
      Approx. 16ms
      Approx. 204ms
      Approx. 262ms



    2. A093225E01
    3. WAVEFORM 2:
      Engine speed signal
      ECM Terminal Names
      Between TACH and E1
      Tester Ranges
      5 V/DIV, 10 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.