Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabetic codes in the table below.



B085808E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least for 90 seconds after disconnecting the cable to prevent the airbag from working.


3. REMOVE FRONT FLOOR FOOTREST


    B087437E01
  1. Disengage the 2 clips and remove the front floor footrest.



4. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab)


    B087476E01
  1. Disengage the 8 claws and clip, and remove the front door scuff plate.



5. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab)


    B087436E01
  1. Disengage the 9 claws and clip, and remove the front door scuff plate.



6. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab)


    B087411E01
  1. Disengage the 9 claws and remove the front door scuff plate.



7. REMOVE FRONT DOOR SCUFF PLATE RH (for Regular Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



8. REMOVE FRONT DOOR SCUFF PLATE RH (for Access Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



9. REMOVE FRONT DOOR SCUFF PLATE RH (for Double Cab)

HINT:
Follow the same procedures as for the front door scuff plate LH.



10. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



11. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



12. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



13. REMOVE COWL SIDE TRIM BOARD RH (for Regular Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



14. REMOVE COWL SIDE TRIM BOARD RH (for Access Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



15. REMOVE COWL SIDE TRIM BOARD RH (for Double Cab)

HINT:
Follow the same procedures as for the cowl side trim board LH.



16. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip LH.



17. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip RH.



18. REMOVE FRONT PILLAR GARNISH LH (for Regular Cab)


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the clip and claw and remove the front pillar garnish.



    B087596E01
  1. for LH Side:

    1. Using a clip remover, remove the 3 wire harness clamps.



19. REMOVE FRONT PILLAR GARNISH LH (for Access Cab)


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the claw and clip, and remove the front pillar garnish.



    B087596E01
  1. for LH Side:

    1. Using a clip remover, remove the 3 wire harness clamps.



20. REMOVE FRONT PILLAR GARNISH LH (for Double Cab)


    B087443E02
  1. Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



    B087444E01
  1. Remove the 2 screws.

  1. Disengage the clip and claw and remove the front pillar garnish.



    B087596E01
  1. for LH side:

    1. Using a clip remover, remove the 3 wire harness clamps.



    B087597E02
  1. w/ Curtain Shield Airbag:

    NOTICE:
    Cover the curtain shield airbag with the protective cover as soon as the front pillar garnish is removed.


    1. Thoroughly cover the air bag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.



21. REMOVE FRONT PILLAR GARNISH RH (for Regular Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



22. REMOVE FRONT PILLAR GARNISH RH (for Access Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



23. REMOVE FRONT PILLAR GARNISH RH (for Double Cab)

HINT:
Follow the same procedures as for the front pillar garnish LH.



24. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.



25. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Disengage the 4 clips and remove the instrument panel hole cover.



26. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085768E01
  1. Remove the shift knob.

  1. Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.



27. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



28. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



29. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B085773E01
  1. Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.



30. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)


    B085777E01
  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



31. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    B085813E01
  1. Remove the shift knob.

  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



32. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)


    B085810E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085812E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



33. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)


    B085774E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085776E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



34. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    B085778E01
  1. Using a screwdriver, disengage the 4 clips and remove the air conditioning control assembly.

    HINT:
    Tape up the screwdriver tip before use.

  1. Disconnect the 2 connectors.



35. REMOVE RADIO RECEIVER ASSEMBLY


E075957
  1. Remove the 4 bolts.

  1. Disconnect the connector and remove the radio receiver assembly with bracket.



36. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088397E01
  1. Disengage the 2 claws.



    B088394
  1. Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.



37. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    B085780E01
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.

  1. Disconnect the connectors.



38. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085781E01
  1. Remove the 2 clips.

  1. Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.

  1. Disconnect the connectors.



39. REMOVE COMBINATION METER ASSEMBLY


    B085782E01
  1. Remove the 4 screws <E> and the combination meter assembly.

  1. Disconnect the 2 connectors.



40. REMOVE INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.



41. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B085785E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.

  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B085786E01
  1. Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.



42. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH


    B085787E01
  1. Remove the bolt <B>.

  1. Disengage the 2 clips and remove the instrument panel lower finish panel sub-assembly RH.



43. REMOVE LOWER INSTRUMENT PANEL LH


    B085788E01
  1. Remove the 3 bolts <B> and the lower instrument panel LH.



44. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Remove the bolt <B>.

  1. Disengage the 5 clips and remove the instrument lower cover sub-assembly.

  1. Disconnect the 2 connectors.



45. REMOVE INSTRUMENT SIDE PANEL RH


    B085790E01
  1. Using a screwdriver, disengage the 3 claws and remove the instrument side panel RH.

    HINT:
    Tape up the screwdriver tip before use.



46. DISCONNECT PASSENGER AIRBAG CONNECTOR


F050426E01
  1. Disconnect the airbag connector.



47. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY W/ PASSENGER AIRBAG ASSEMBLY


    B085807E01
  1. Tape up the steering column cover upper and steering wheel sub-assembly in protective tape.

  1. Disengage the 4 clamps and disconnect the 4 connectors.



  1. Remove the 8 bolts, nut and instrument panel sub-assembly w/ passenger air bag assembly.


    B085804E01



48. REMOVE DEFROSTER NOZZLE ASSEMBLY W/ NO.2 HEATER TO REGISTER DUCT


    B085793E01
  1. Remove the 5 screws <D> and defroster nozzle assembly w/ No. 2 heater to register duct.



49. REMOVE FOUR WHEEL DRIVE CONTROL ECU


    B085794E01
  1. Remove the 2 screws <D> and four wheel drive control ECU.



50. REMOVE DOOR CONTROL RECEIVER


    B085795E01
  1. Remove the 2 screws <D> and door control receiver.



51. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY


F050428E01
  1. Disengage the 10 hooks and remove the front passenger airbag.

  1. Release the front side wall of the airbag door from the other hook and remove the front passenger airbag assembly.



52. REMOVE NO.1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B085796E01
  1. Remove the 4 screws <D> and No. 1 instrument panel register assembly.



53. REMOVE INSTRUMENT PANEL CENTER BRACKET SUB-ASSEMBLY


    B085797E01
  1. Remove the screw <D> and instrument panel center bracket sub-assembly center.



54. REMOVE ANTENNA CORD SUB-ASSEMBLY



E075961E01

  1. Disengage the 4 claws and remove the radio antenna cord sub-assembly.



55. REMOVE NO. 1 INSTRUMENT PANEL PIN


    B085792E01
  1. Remove the 4 screws <D> and the 4 No. 1 instrument panel pins.



56. REMOVE INSTRUMENT PANEL CUSHION


57. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY