Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Separate Folding Seat Type)

FRONT SEAT ASSEMBLY (for Separate Folding Seat Type) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp surfaces on the front seat back spring and front seat with adjuster frame could cause injuries to your hands.



1. INSTALL SEAT WIRE


    B087367E01
  1. Install the 3 wire harness clamps and connector clamp.

  1. Connect the 4 connectors.



2. INSTALL OCCUPANT CLASSIFICATION ECU


    B087366E01
  1. Engage the claw and install the occupant classification ECU.

  1. Connect the 2 connectors.



3. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH


    B087365E01
  1. Install the reclining adjuster outside cover with the screw.



4. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

HINT:
Follow the same procedures as for the reclining adjuster outside cover LH.



5. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B087364E01
  1. Install the reclining adjuster inside cover with the screw.



6. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Follow the same procedures as for the reclining adjuster inside cover LH.



7. INSTALL FRONT SEAT CUSHION COVER


    B113921E02
  1. Using hog ring pliers, install the front seat cushion cover with new hog rings.

    NOTICE:
    1. Do not contaminate or scratch the front seat cushion cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.



8. INSTALL FRONT SEAT CUSHION ASSEMBLY


    B087368E01
  1. Engage the 2 claws and 3 hooks, and install the front seat cushion.



    B113922E02
  1. Hook the front seat cushion cover to the front seat with adjuster frame.

  1. Using hog ring pliers, install new hog rings.



9. INSTALL FRONT SEAT BACK COVER


    B113928E02
  1. Using hog ring pliers, install the front seat back cover with new hog rings.

    NOTICE:
    1. Do not contaminate or scratch the front seat back cover.
    2. When installing hog rings, minimize wrinkles as far as possible.



10. INSTALL FRONT SEAT BACK SPRING ASSEMBLY


    B121730E01
  1. w/ Front Seat Side Airbag:

    1. Install the front seat back spring into the front seat back pad.

    2. Install the hook tape.

    3. Using hog ring pliers, install new hog rings.

    4. Fully cover the air bag with the inner hook and tighten the bolt.

      Torque:
      5.5 N*m{ 55 kgf*cm , 49 in.*lbf }

      NOTICE:
      1. For vehicles with side air bag, the front seat back cover must be securely installed. Otherwise, the side air bag may not deploy properly.
      2. Make sure that the strap is not twisted after installing the inner hook.
      3. Install the inner hook securely.

  1. w/o Front Seat Side Airbag:

    1. Install the front seat back spring into the front seat back pad.

    2. Install the hook tape.

    3. Using hog ring pliers, install new hog rings.



11. INSTALL FRONT SEAT HEADREST SUPPORT


B087358E01

HINT:
Follow the same procedures as for the opposite side.

  1. Engage the 2 claws and install the front seat headrest support.



12. INSTALL FRONT SEAT BACK LOCK HANDLE ROD


    B087357E01
  1. Install the front seat back lock handle rod.



13. INSTALL FRONT SEAT HINGE COVER LH


    B087356E01
  1. Engage the 2 claws and install the front seat hinge cover.



14. INSTALL FRONT SEAT HINGE COVER RH

HINT:
Follow the same procedures as for the seat hinge cover LH.



15. INSTALL FRONT SEAT BACK LOCK SUB-ASSEMBLY LH


    B087369E01
  1. Install the front seat back lock with the 2 bolts.

    Torque:
    43 N*m{ 440 kgf*cm , 32 ft.*lbf }



16. INSTALL FRONT SEAT BACK LOCK SUB-ASSEMBLY RH

HINT:
Follow the same procedures as for the front seat back lock LH.



17. INSTALL FRONT SEAT BACK BOARD


    B087354E01
  1. Engage the 2 claws and 2 clips, and install the front seat back board.



18. INSTALL FRONT SEAT BACK ASSEMBLY


    B087353E01
  1. Install the front seat back with the 4 bolts.

    Torque:
    43 N*m{ 440 kgf*cm , 32 ft.*lbf }



19. INSTALL FRONT SEAT BACK SHIELD LH


    B087352E01
  1. Engage the 3 claws and install the front seat back shield.

  1. Tighten the screw.



20. INSTALL FRONT SEAT BACK SHIELD RH


    B088591E02
  1. w/ Front Seat Side Airbag:

    1. The front seat side air bag wire must pass between protector plate and the front seat back shield.

      HINT:
      Tune "W" to be able to thread the front seat side airbag wire and clips through.



    2. B088186E01
    3. Engage the 4 claws and install the front seat side air bag wire.



    4. B088192E01
    5. Engage the 3 claws and install the front seat back shield.

    6. Tighten the screw.



    7. B088187
    8. Install the wire harness clamp and connector clamp.



    B088192E01
  1. w/o Front Seat Side Airbag:

    1. Engage the 3 claws and install the front seat back shield.

    2. Tighten the screw.



21. INSTALL RECLINING ADJUSTER RELEASE KNOB LH


    B087351E01
  1. Engage the claw and install the reclining adjuster release handle.



22. INSTALL RECLINING ADJUSTER RELEASE KNOB RH

HINT:
Follow the same procedures as for the reclining adjuster release handle LH.



23. INSTALL FRONT SEAT CUSHION SHIELD


    B087350E01
  1. Engage the 2 claws and clip, and install the front seat cushion shield.

  1. Tighten the screw.



24. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B087370E01
  1. Engage the claw and install the reclining adjuster release handle.



25. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B087348E01
  1. Engage the claw and clip, and install the front seat cushion inner shield.

  1. Tighten the screw.



26. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B087321E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Be careful not to place the front seat inner belt over the convex areas of the front seat with adjuster frame.

  1. Check that the front seat inner belt rotates smoothly.

  1. Install the wire harness clamp and connector clamp.

  1. Connect the seat wire No. 1 connector.



27. INSTALL FRONT SEAT HEADREST ASSEMBLY


    B087347E02
  1. Disengage the lock button of the front seat headrest support and install the front seat headrest.