Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > DISASSEMBLY

for Preparation Click here



1. INSPECT BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION


R012683E03
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Backlash:
    0.11 to 0.21 mm (0.0043 to 0.0083 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



2. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


FA01158
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Torque:
    0.49 to 0.78 N*m{ 5 to 8 kgf*cm , 4.3 to 6.9 in.*lbf }

    If necessary, disassemble and inspect the differential assembly.



3. INSPECT TOTAL PRELOAD
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.22 to 0.88 N*m (2.2 to 8.8 kgf*cm, 2.0 to 7.8 in.*lbf)

    If necessary, disassemble and inspect the differential.



4. REMOVE DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY


G023135
  1. Remove the 4 bolts.

  1. Using a hammer handle, remove the actuator assembly.



5. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY


G023134
  1. Remove the 4 bolts.

  1. Using a plastic hammer, remove the differential tube.



6. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


R013209E01
  1. Using SST, remove the oil seal.

    SST
    09308-00010  



7. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY


G023136E02
  1. Using SST, remove the side gear inter shaft.

    SST
    09350-20015   (09369-20040)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

  1. Remove the snap ring from the side gear inter shaft.



8. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F044234E01
  1. Using SST and a hammer, remove the nut.

    SST
    09930-00010  



    SA02349E05
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021  



    F052175E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



9. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


SA02348E03
  1. Using SST, remove the oil seal from the differential carrier assembly.

    SST
    09308-10010  



10. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


11. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


Z000641E04
  1. Using SST, remove the rear bearing from the drive pinion.

    SST
    09556-22010  

  1. Remove the bearing spacer.



12. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Using a screwdriver, remove the union.

  1. Remove the 10 bolts and tap out the side bearing retainer with a plastic hammer.



13. REMOVE DIFFERENTIAL CASE ASSEMBLY


14. REMOVE DIFFERENTIAL DRIVE PINION


15. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


R002482E02
  1. Using SST and a press, remove the front bearing and washer from the drive pinion.

    SST
    09950-00020  

    HINT:
    If the drive gear or ring gear is damaged, replace them as a set.



16. REMOVE FRONT BEARING OUTER RACE


R013226
  1. Using a brass bar and a hammer, remove the front bearing outer race.



17. REMOVE REAR BEARING OUTER RACE


F044257E01
  1. Using SST, remove the rear bearing outer race.

    SST
    09502-12010  
    09612-65014   (09612-01020, 09612-01050)

  1. Using a brass bar and a hammer, remove the oil storage ring.



18. REMOVE FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR
  1. Using a brass bar and hammer, remove the side bearing retainer deflector by tapping it gently.



19. REMOVE SIDE BEARING OUTER RACE


R013211E01

HINT:
  1. Measure the plate washer and note its thickness.
  2. Tag the bearing outer races to show the location for reassembly.

  1. Using SST and a press, remove the outer race and plate washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



    R013213E01
  1. Using SST and a press, remove the outer race and plate washer from the differential carrier assembly.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)



20. REMOVE DIFFERENTIAL RING GEAR
  1. Place matchmarks on the ring gear and differential case assembly.

  1. Remove the 10 bolts.

  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case assembly.



21. REMOVE FRONT DIFFERENTIAL CASE BEARING


R011392E02
  1. Using SST, remove the 2 differential case bearings from the differential case assembly.

    SST
    09950-60010   (09951-00390)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

    HINT:
    Fix the claws of SST into the notch in the differential case assembly.



22. DISASSEMBLE DIFFERENTIAL CASE


RA00997
  1. Using a pin punch and a hammer, remove the straight pin.

  1. Remove these parts from the differential case assembly.

    1. 2 Differential side gears

    2. 2 Differential side gear thrust washers

    3. Differential pinion shaft

    4. 2 Differential pinion gears

    5. 2 Differential pinion gear thrust washers



23. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that there is no damage to the pinion gear and side gear.
    If the pinion gear and/or side gear is damaged, replace the differential gear kit.



24. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case assembly is not damaged.
    If the differential case assembly is damaged, replace it.



25. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING


SA00353
  1. Using a brass bar and hammer, remove the 2 bearings.



26. REMOVE DIFFERENTIAL CLUTCH HUB


G023137
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the differential clutch hub.



27. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


R013199E01
  1. Using SST, remove the oil seal from the differential tube.

    SST
    09308-00010  



28. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


C097022
  1. Using a snap ring expander, remove the snap ring.

  1. Remove the side gear shaft from the differential tube.



29. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


R013420E02
  1. Using a snap ring expander, remove the snap ring.

  1. Using SST, a brass bar and a press, remove the bearing.

    SST
    09950-00020  

    NOTICE:
    Do not damage the bearing.



30. REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR


R004465E01
  1. Using SST, a socket wrench and a press, remove the dust deflector.

    SST
    09950-00020  



31. REMOVE DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB


G023141
  1. Check for wear and damage to the clutch hub and clutch sleeve.
    If necessary, replace them.

  1. Check that the clutch sleeve slides smoothly on the clutch hub.



32. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE


G023144
  1. Check for wear and damage to the clutch hub and side gear inter shaft.

  1. Check that the clutch sleeve slides smoothly on the side gear inter shaft.



33. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE


G023142
  1. Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the fork or clutch sleeve.