Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL DUST DEFLECTOR


G022166E01
  1. Using a steel plate and a press, install a new dust deflector.

    NOTICE:
    Do not damage the dust deflector.



2. INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING


R013421E02
  1. Using SST and a press, install the bearing.

    SST
    09223-00010  

  1. Using a snap ring expander, install the snap ring.



3. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH


C097022
  1. Install the side gear shaft into the differential tube.

  1. Using snap ring pliers, install the snap ring.



4. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


R013419E01
  1. Using SST and a plastic hammer, install a new oil seal.

    SST
    09608-32010  

    Oil seal drive in depth:
    4.8 to 0.58 mm (0.1890 to 0.2284 in.)

  1. Coat the oil seal lip with MP grease.



5. INSTALL DIFFERENTIAL CLUTCH HUB


G023138
  1. Install the clutch hub onto the side gear inter shaft.

  1. Using snap ring pliers, install the snap ring.

    NOTICE:
    Be sure to install the differential clutch hub in the correct direction.



6. INSTALL FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING


SA00355E02
  1. Using SST and a press, install 2 new bearings.

    SST
    09950-60010   (09951-00380)

    Bearing press in depth:
    1.4 to 2.0 mm (0.055 to 0.079 in.)



7. INSTALL FRONT DIFFERENTIAL CASE


FA01121
  1. Install the 2 proper thrust washers onto the 2 side gears.

    HINT:
    Using the table below, select a thrust washer which will ensure that the backlash is within the specifications.

    Washer thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    1.50 (0.0591)
    1.75 (0.0689)
    1.55 (0.0610)
    1.80 (0.0709)
    1.60 (0.0630)
    1.85 (0.0728)
    1.65 (0.0650)
    1.90 (0.0748)
    1.70 (0.0669)
    -

  1. Install the 2 side gears, 2 side gear thrust washers, 2 pinion gears, 2 pinion gear thrust washers and pinion shaft into the differential case assembly.

    HINT:
    Align the holes of the differential case assembly and pinion shaft.



  1. Measure the side gear backlash.



      F043636
    1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case assembly.

      Backlash:
      0 to 0.15 mm (0 to 0.0059 in.)

      If the backlash is not within the specification, install a side gear thrust washer with a different thickness.



    FA01124
  1. Using a pin punch and hammer, install the straight pin through the differential case assembly and hole of the pinion shaft.

  1. Stake the differential case assembly.



8. INSTALL DIFFERENTIAL RING GEAR


SA02160E02
  1. Clean the contact surfaces of the differential case assembly and ring gear.

  1. Heat the ring gear to about 100°C (212°F) in boiling water.

  1. Carefully take the ring gear out of the boiling water.

  1. After any moisture on the ring gear has completely evaporated, quickly install the ring gear onto the differential case assembly.

    HINT:
    Align the matchmarks on the ring gear and differential case assembly.

  1. Temporarily install 10 bolts so that the bolt holes in the ring gear and differential case assembly are aligned.

  1. After the ring gear has cooled sufficiently, tighten the ring gear set bolts to which thread lock has been applied.

    Torque:
    97 N*m{ 984 kgf*cm , 71 ft.*lbf }

    Thread lock:
    Part No. 08833-00100, THREE BOND 1360k or equivalent



9. INSTALL FRONT DIFFERENTIAL CASE BEARING


R013784E01
  1. Using SST and a press, install the 2 differential case bearings into the differential case assembly.

    SST
    09226-10010  



10. INSTALL SIDE BEARING OUTER RACE

HINT:
When replacing the 2 differential case bearings, fit 2 of the thinnest new washers to each bearing and when reusing the bearings, fit washers of the same thickness as those removed.

  1. Install a new plate washer to the side bearing retainer.



    R013375E02
  1. Using SST and a press, install the bearing outer race onto the differential case bearing retainer assembly.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)

  1. Install a new plate washer onto the differential carrier assembly.



    R013375E02
  1. Using SST and a press, install the bearing outer race onto the differential carrier assembly.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)



11. INSTALL FRONT BEARING OUTER RACE


R013281E02
  1. Using SST, install the outer race.

    SST
    09950-00020   (09951-00680, 09951-00890)



12. INSTALL REAR BEARING OUTER RACE
  1. Install the oil storage ring.

  1. Using SST, install the outer race.

    SST
    09950-00020   (09951-00680, 09951-00890)



13. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING
  1. Install the washer onto the drive pinion.

    HINT:
    First, fit a washer of the same thickness as the removed washer, then after checking the tooth contact pattern, replace the washer with one of a differential thickness if necessary.



    R001197E01
  1. Using SST and a press, install the front bearing onto the drive pinion.

    SST
    09506-30012  



14. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
  1. Install the drive pinion.

    HINT:
    Assemble the spacer and oil seal after adjusting the ring gear tooth contact pattern.



    R011163E05
  1. Using SST, install the rear bearing, oil slinger and companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

  1. Coat the threads of the nut with hypoid gear oil.



    SA02347E03
  1. Adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the companion flange, tighten the nut.

    SST
    09330-00021  

    NOTICE:
    As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.



    SA02352
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Bearing
    Standard
    New
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
    Reused
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



15. INSTALL DIFFERENTIAL CASE ASSEMBLY


16. ADJUST BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION
  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



    R012683E03
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Backlash:
    0.11 to 0.21 mm (0.0043 to 0.0083 in.)

  1. If it is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

    HINT:
    There should be no clearance between the plate washer and differential case.
    Make sure that there is ring gear backlash.


    Washer thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.58 (0.0622)
    1.78 (0.0701)
    1.98 (0.0780)
    1.60 (0.0630)
    1.80 (0.0709)
    2.00 (0.0787)
    1.62 (0.0638)
    1.82 (0.0717)
    2.02 (0.0800)
    1.64 (0.0646)
    1.84 (0.0724)
    2.04 (0.0803)
    1.66 (0.0654)
    1.86 (0.0732)
    2.06 (0.0811)
    1.68 (0.0661)
    1.88 (0.0740)
    2.08 (0.0819)
    1.70 (0.0669)
    1.90 (0.0748)
    2.10 (0.0827)
    1.72 (0.0677)
    1.92 (0.0756)
    2.12 (0.0835)
    1.74 (0.0685)
    1.94 (0.0764)
    2.14 (0.0843)
    1.76 (0.0693)
    1.96 (0.0772)
    2.16 (0.0850)



17. INSPECT TOTAL PRELOAD


SA02352
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.22 to 0.88 N*m (2.2 to 8.8 kgf*cm, 2.0 to 7.8 in.*lbf)

    If necessary, disassemble and inspect the differential.



18. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
  1. Remove the side bearing retainer and differential case assembly.



    R013220
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead.

  1. Install the differential case assembly and side bearing retainer.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Hold the companion flange firmly and rotate the ring gear in both directions.

  1. Remove the differential case, side bearing retainer and differential case assembly.



  1. Inspect the tooth contact pattern.


    F052199E01

    If the teeth are not engaged properly, use the following chart to select the appropriate washer for correction.

    FA02008E01

    Washer thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.70 (0.0669)
    1.94 (0.0764)
    2.18 (0.0858)
    1.73 (0.0681)
    1.97 (0.0776)
    2.21 (0.0870)
    1.76 (0.0693)
    2.00 (0.0787)
    2.24 (0.0882)
    1.79 (0.0705)
    2.03 (0.0799)
    2.27 (0.0894)
    1.82 (0.0717)
    2.06 (0.0811)
    2.30 (0.0906)
    1.85 (0.0728)
    2.09 (0.0823)
    2.33 (0.0917)
    1.88 (0.0740)
    2.12 (0.0835)
    -
    1.91 (0.0752)
    2.15 (0.0847)
    -



    SA02349E05
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021  



    R011391E02
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



    Z000641E03
  1. Using SST, remove the rear bearing from the drive pinion.

    SST
    09556-22010  



19. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new bearing spacer and oil storage ring.



20. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


21. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


22. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT
  1. Place the companion flange on the drive pinion.

  1. Coat the threads of a new nut with hypoid gear oil LSD.



    R011163E06
  1. Using SST and the companion flange, install the rear tapered roller bearing, then remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



23. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL


R013417E02
  1. Using SST and a hammer, install the oil seal.

    SST
    09554-22010  

    Oil seal drive in depth:
    3.9 to 4.8 mm (0.153 to 0.189 in.)

  1. Coat the oil seal lip with MP grease.



    SA02351E05
  1. Using SST to hold the flange, tighten the nut.

    Torque:
    370 N*m{ 3,773 kgf*cm , 273 ft.*lbf }

    SST
    09330-00021  



24. INSTALL DIFFERENTIAL SIDE BEARING RETAINER


R013200E02
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.

  1. Clean the contact surfaces of any residual FIPG material using gasoline or alcohol.

  1. Apply FIPG to the side bearing retainer, as shown.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

    HINT:
    Install the side bearing retainer within 10 minutes of applying FIPG.

  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the union.



25. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


SA02352
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Bearing
    Standard
    New
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
    Reused
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    If the preload is greater than the specification, replace the bearing spacer.
    If the preload is less than the specification, retighten the nut to 13 N*m (130 kgf*cm, 9 ft*lbf) a little at a time until the specified preload is reached.

    Torque:
    370 N*m{ 3,773 kgf*cm , 273 ft.*lbf } or less

    If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repair the preload procedure. Do not loosen the nut to reduce the preload.



26. INSPECT TOTAL PRELOAD


SA02352
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.22 to 0.88 N*m (2.2 to 8.8 kgf*cm, 2.0 to 7.8 in.*lbf)

    If necessary, disassemble and inspect the differential.



27. INSPECT BACKLASH DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION
SST
09564-32011  


    R012683E03
  1. Using SST and a dial indicator, measure the ring gear backlash.

    Backlash:
    0.11 to 0.21 mm (0.0043 to 0.0083 in.)

  1. If it is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

    HINT:
    There should be no clearance between the plate washer and differential case.
    Make sure that there is ring gear backlash.


    Washer thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.58 (0.0622)
    1.78 (0.0701)
    1.98 (0.0780)
    1.60 (0.0630)
    1.80 (0.0709)
    2.00 (0.0787)
    1.62 (0.0638)
    1.82 (0.0717)
    2.02 (0.0800)
    1.64 (0.0646)
    1.84 (0.0724)
    2.04 (0.0803)
    1.66 (0.0654)
    1.86 (0.0732)
    2.06 (0.0811)
    1.68 (0.0661)
    1.88 (0.0740)
    2.08 (0.0819)
    1.70 (0.0669)
    1.90 (0.0748)
    2.10 (0.0827)
    1.72 (0.0677)
    1.92 (0.0756)
    2.12 (0.0835)
    1.74 (0.0685)
    1.94 (0.0764)
    2.14 (0.0843)
    1.76 (0.0693)
    1.96 (0.0772)
    2.16 (0.0850)



28. INSPECT AND ADJUST FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY FRONT


F001237E03
  1. Using a dial indicator, measure the runout of the drive pinion companion flange vertically and horizontally.

    Maximum runout:
    Vertical runout: 0.10 mm (0.0039 in.)
    Lateral runout: 0.10 mm (0.0039 in.)

    If the runouts are not within the specifications, replace the companion flange.



29. INSTALL FRONT DRIVE PINION COMPANION FLANGE FRONT NUT


ZK07449
  1. Using a chisel and hammer, stake the drive pinion nut.



30. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


F044255E01
  1. Using SST and a plastic hammer, install a new oil seal until its surface is flush with the differential carrier end.

    SST
    09608-32010  

  1. Coat the oil seal lip with MP grease.

    Oil seal driven in depth:
    -0.45 to 0.45 mm (-0.0177 to 0.0177 in.)



31. INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY


G023139
  1. Install a new snap ring onto the side gear inter shaft.

  1. Using a plastic hammer, install the side gear inter shaft onto the differential case.

  1. Check that there are 2 to 3 mm (0.08 to 0.12 in.) of play in the axial direction.

  1. Check that the side gear inter shaft will not come out by trying to pull it completely out by hand.



32. INSTALL FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR


G023145
  1. Using a brass bar and a hammer, install the side bearing retainer deflector.

    NOTICE:
    Be sure to install the side bearing retainer deflector in the correct direction.



33. INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY


F044256E01
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential and clutch case.

  1. Clean the contact surfaces of any residual FIPG material using gasoline or alcohol.

  1. Apply FIPG to the differential, as shown.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

    HINT:
    Install the differential tube within 10 minutes of applying FIPG.

  1. Install the differential tube into the differential carrier assembly.



    G023134
  1. Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.

  1. Apply adhesive to 2 to 3 threads of each bolt end.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

  1. Install the 4 bolts.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf } or less



34. INSTALL DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY


G023140
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the actuator and clutch case.

  1. Clean the contact surfaces of any residual FIPG material using gasoline or alcohol.

  1. Apply FIPG to the differential tube, as shown.

    FIPG:
    Part No. 08826-00090, THREE BOND 1281 or equivalent

    HINT:
    Install the actuator within 10 minutes of applying FIPG.



    G023143
  1. Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.

  1. Install the actuator assembly onto the differential tube.

  1. Apply adhesive to 2 to 3 threads of each bolt end.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1281 or equivalent

  1. Install the 4 bolts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }