Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > DISASSEMBLY

for Preparation Click here



1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


F051367
  1. Fix the rear differential carrier to the overattachment.



2. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F001237E03
  1. Using a dial indicator, measure the vertical and horizontal runout of the companion flange.

    Maximum runout:
    Vertical runout: 0.10 mm (0.0039 in.)
    Lateral runout: 0.10 mm (0.0039 in.)

    If the runouts are not within the specifications, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


F051355
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.05 mm (0.0020 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


F051386
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    0.78 to 1.05 N*m (8.0 to 11 kgf*cm, 6.9 to 9.3 in.*lbf)



6. INSPECT TOTAL PRELOAD


C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If necessary, disassemble and inspect the differential.



7. REMOVE REAR DRIVE PINION NUT


F044346E02
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  



    SA02349E06
  1. Using SST to hold the drive pinion companion flange, remove the nut.

    SST
    09330-00021  



8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR


F052175E03
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)



9. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


F040564E04
  1. Using SST and a press, remove the dust deflector.

    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  



10. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


SA02348E03
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  



11. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


Z000641E04
  1. Using SST, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09556-22010  



12. REMOVE DIFFERENTIAL CASE ASSEMBLY


F051357E01
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and bearing cap.



    F051358E01
  1. Using SST and a plastic hammer, remove the 2 side bearing plate washers.

    HINT:
    Measure the plate washer thickness and note it down.

    SST
    09504-22011  

  1. Remove the differential case with the bearing outer races from the carrier.

    HINT:
    Tag the disassembled parts to show the locations for reassembly.



13. REMOVE DIFFERENTIAL DRIVE PINION


C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier.



14. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


R010668E02
  1. Using SST and a press, remove the drive pinion tapered roller bearing from the drive pinion.

    SST
    09950-00020  

    HINT:
    If either the drive pinion or ring gear are damaged, replace them as a set.



15. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


16. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


F044358E02
  1. Using SST, remove the front tapered roller bearing from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and a hammer, remove the oil storage ring from the carrier.



17. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


C091047
  1. Using a brass bar and a hammer, remove the rear tapered roller bearing from the carrier.



18. REMOVE DIFFERENTIAL RING GEAR


F051360E01
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 12 ring gear set bolts.



    C014054
  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case.



19. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT


F051361
  1. Install the rear differential case bearing onto the differential case.

  1. Install the differential case onto the differential carrier.

  1. Using a dial indicator, measure the differential case runout.

    Maximum case runout:
    0.05 mm (0.0020 in.)

  1. Remove the differential case.



20. REMOVE REAR DIFFERENTIAL CASE BEARING


F051362E01
  1. Using SST, remove the 2 rear differential case bearings from the differential case.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00480)

    HINT:
    Fix the claws of SST into the notch in the differential case.



21. DISASSEMBLE DIFFERENTIAL CASE (2 PINION DIFFERENTIAL)


F051388
  1. Using a pin punch and hammer, remove the straight pin.

  1. Remove the pinion shaft, 2 pinion gears, pinion gear thrust washers, side gears and side gear thrust washers from the differential case.



22. DISASSEMBLE DIFFERENTIAL CASE (W/ LSD DIFFERENTIAL)


F051391E01
  1. Place matchmarks on the LH and RH cases.

  1. Remove the 8 bolts uniformly, a little at a time.

  1. Using a plastic hammer, separate the LH and RH cases.



    F052185E02
  1. Remove these parts from the LH case.
    A
    side gear
    B
    side gear thrust washer
    C
    clutch plates

    HINT:
    1. Keep the disassembled parts in order.
    2. Face the rough side of the thrust washer marked by # to the differential case.



    C089315E02
    F052186E02
  1. Remove these parts from the RH case.
    A
    Spider
    B
    Differential pinion gear
    C
    Compression spring
    D
    Spring LH retainer
    E
    Spring RH retainer
    F
    Pinion gear thrust washer
    G
    Side gear
    H
    side gear thrust washer
    I
    clutch plate

    HINT:
    Face the rough side of the thrust washer marked by # to the differential case.