REAR DIFFERENTIAL CARRIER OIL SEAL > INSTALLATION |
| 1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
Install a new rear differential drive pinion bearing spacer.
| 2. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
Using a brass bar and a hammer, install a new oil storage ring.
Using SST and a hammer, install the front bearing outer race.
Install the front bearing.
| 3. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER (w/ Differential Lock) |
| 4. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST and a hammer, install a new oil seal.
Coat oil seal lip with MP grease.
| 5. INSTALL REAR DRIVE COMPANION FLANGE SUB-ASSEMBLY REAR |
![]() |
Using SST, install the companion flange.
Coat the threads of a new nut with hypoid gear oil LSD.
![]() |
Using SST to hold the companion flange, tighten the nut.
| 6. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload of backlash between the drive pinion and ring rear.
| 7. INSTALL REAR DRIVE PINION NUT |
![]() |
Using a chisel and a hammer, stake the nut.
| 8. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD Drive Type, Regular Cab) |
![]() |
Remove SST from the extension housing.
Install the propeller shaft assembly into the extension housing.
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.
| 9. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 2WD Drive Type, Except Regular Cab) |
![]() |
Remove SST from the extension housing.
Install the propeller shaft into the extension housing.
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
![]() |
Provisionally install the center support bearing with the 2 mounting bolts.
![]() |
Adjust the center support bearing.
Torque the 2 bolts.
| 10. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD Drive Type, Regular Cab) |
![]() |
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft with the 4 nuts and 4 washers.
![]() |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
| 11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (4WD Drive Type, Except Regular Cab) |
![]() |
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft with the 4 nuts and 4 washers.
![]() |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
![]() |
Provisionally install the center support bearing with 2 mounting bolts.
Torque the 2 bolts.
| 12. FILL UP DIFFERENTIAL OIL |
![]() |
Stop the vehicle on a level place.
Remove the differential filler plug and gasket.
Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.
Check for oil leakage if the oil level is low.
Install the differential filler plug and a new gasket.
| 13. INSPECT DIFFERENTIAL OIL |
![]() |
Stop the vehicle on a level place.
Remove the differential filler plug and gasket.
Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.
Check for oil leakage if the oil level is low.
Install the differential filler plug and a new gasket.
| 14. INSPECT FOR DIFFERENTIAL OIL LEAKAGE |