Home › SUSPENSION & AXLE › SUSPENSION › FRONT WHEEL ALIGNMENT (for 2WD)

FRONT WHEEL ALIGNMENT (for 2WD) > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:

    Tire Size
    Front Wheel
    kPa (kgf/cm2, psi)
    Rear Wheel
    kPa (kgf/cm2, psi)
    Spare Wheel
    kPa (kgf/cm2, psi)
    P215/70R15 97S
    200 (2.0, 29)
    220 (2.2, 32)
    220 (2.2, 32)
    P255/45R18 99V
    240 (2.4, 35)
    240 (2.4, 35)
    240 (2.4, 35)
    P245/75R16 109S
    200 (2.0, 29)
    200 (2.0, 29)
    200 (2.0, 29)
    P265/70R16 111T
    200 (2.0, 29)
    220 (2.2, 32)
    220 (2.2, 32)
    P265/65R17 110S
    200 (2.0, 29)
    200 (2.0, 29)
    200 (2.0, 29)



    R003031
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less



2. MEASURE VEHICLE HEIGHT



F051670E01


Vehicle height::

Vehicle Model
Tire Size
A - B
C - D
TRN220L-TRMDKA
P215/70R15
87 mm (3.43 in.)
48 mm (1.89 in.)
TRN220L-TRPDKA
P215/70R15
88 mm (3.46 in.)
48 mm (1.89 in.)
TRN225L-CRMDKA
P215/70R15
86 mm (3.39 in.)
50 mm (1.97 in.)
TRN225L-CRPDKA
P215/70R15
87 mm (3.43 in.)
50 mm (1.97 in.)
GRN225L-CRFDKA
P255/45R18
118 mm (4.65 in.)
85 mm (3.35 in.)

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of adjustment cam bolt center (front side)
C:
Ground clearance of rear wheel center
D:
Ground clearance of rear leaf spring front side bush center

NOTICE:
Before inspecting the wheel alignment, check the vehicle height.

Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.


3. INSPECT TOE-IN


SA03213E05

Toe-in:

Vehicle Model
Tire Size
A + B
C - D
TRN220L-TRMDKA
P215/70R15
4.8' +- 6.5' (0.081° +- 0.108°)
0.96 +- 2 mm (0.038 +- 0.08 in.)
TRN220L-TRPDKA
P215/70R15
4.3' +- 6.5' (0.072° +- 0.108°)
0.86 +- 2 mm (0.034 +- 0.08 in.)
TRN225L-CRMDKA
P215/70R15
5.3' +- 6.5' (0.089° +- 0.108°)
1.06 +- 2 mm (0.042 +- 0.08 in.)
TRN225L-CRPDKA
P215/70R15
4.8' +- 6.5' (0.081° +- 0.108°)
0.96 +- 2 mm (0.038 +- 0.08 in.)
GRN225L-CRFDKA
P255/45R18
1.8' +- 6.5' (0.030° +- 0.108°)
0.36 +- 2 mm (0.014 +- 0.08 in.)

If the toe-in is not within the specified range, adjust it at the rack ends.


4. ADJUST TOE-IN
  1. Remove the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends uniformly to adjust the toe-in.

    HINT:
    Try to adjust the toe-in to the middle of the specified range.



    F051671
  1. Make sure that the lengths of the right and left rack ends are the same.

  1. Torque the tie rod end lock nuts.

    Torque:
    55.5 N*m{ 566 kgf*cm , 41 ft.*lbf }

  1. Install the boots onto the seats with the clips.

    HINT:
    Make sure that the boots are not twisted.



5. INSPECT WHEEL TURNING ANGLE


SA00028E07
  1. Turn the steering wheel fully, and measure the turning angle.

    Wheel turning angle:
    Inside wheel
    Outside wheel (Reference)
    38°48' (36°48' to 39°48')
    38.80° (36.80° to 39.80°)
    32°30' (30°30' to 33°30')
    32.50° (30.50° to 33.50°)

    If the right and left turning angles of the inside and outside wheels are not within the specified ranges, check the right and left rack end lengths.



6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


Z003382E05
  1. Install the camber-caster-kingpin gauge and position the front wheel on the wheel alignment tester.

  1. Inspect the camber, caster and steering axis inclination.

    Camber, caster and steering axis inclination:

    Vehicle Model
    Tire Size
    Camber
    Caster
    Steering Axis Inclination
    TRN220L-TRMDKA
    P215/70R15
    0°13' +- 45'
    (0.22° +- 0.75°)
    3°52' +- 45'
    (3.86° +- 0.75°)
    10°42' +- 45'
    (10.70° +- 0.75°)
    TRN220L-TRPDKA
    P215/70R15
    0°12' +- 45'
    (0.20° +- 0.75°)
    3°52' +- 45'
    (3.86° +- 0.75°)
    10°44' +- 45'
    (10.73° +- 0.75°)
    TRN225L-CRMDKA
    P215/70R15
    0°14' +- 45'
    (0.24° +- 0.75°)
    4°01' +- 45'
    (4.01° +- 0.75°)
    10°41' +- 45'
    (10.69° +- 0.75°)
    TRN225L-CRPDKA
    P215/70R15
    0°13' +- 45'
    (0.22° +- 0.75°)
    4°01' +- 45'
    (4.02° +- 0.75°)
    10°42' +- 45'
    (10.70° +- 0.75°)
    GRN225L-CRFDKA
    P255/45R18
    -0°40' +- 45'
    (-0.66° +- 0.75°)
    5°09' +- 45'
    (5.15° +- 0.75°)
    11°34' +- 45'
    (11.56° +- 0.75°)

    NOTICE:
    1. Perform the inspection while the vehicle is empty (without spare tires or tools on board).
    2. The tolerance for the difference between the left and right wheels is 30' (0.50°) or less for both the camber and caster.

    If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, recheck the steering knuckle and front wheel for distortion and slack.



7. ADJUST CAMBER AND CASTER

NOTICE:
Inspect the toe-in after the camber has been adjusted.

  1. Loosen the 2 nuts.



  1. Turn the camber adjust cam and adjust the camber and caster.

    HINT:
    Try to adjust the camber and caster to the central value.



    F051672E01



    F051673E01
  1. How to read the adjustment chart (using examples).

    1. Measure the present alignment.

      Camber:
      -0°17' (0.28°)

      Caster:
      3°30' (3.50°)

    2. Calculate the difference between the standard value (A) and the measured value (B) on the adjustment chart.

      Standard value:
      Camber:
      0°13' (0.22°)
      Caster:
      3°50' (3.84°)
      Formula:
      B - A = C
      Camber:
      -0°17' - 0°13' = -0°30'
      Caster:
      3°30' - 3°50' = -0°20'



    3. As shown in the chart, read the distance from the marked point to 0 point, and adjust the front and/or rear adjusting cams accordingly.

      Front adjust cam:
      - (Shorter) 1.9

      Rear adjust cam:
      - (Shorter) 0.8



      F051674E02