Home › DRIVE LINE › VF2BM TRANSFER › TRANSFER CASE OIL SEAL

TRANSFER CASE OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER CASE OIL SEAL


F043487E02
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the case upper surface.

    SST
    09316-60011   (09316-00011)



2. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


F044048E02
  1. Install the companion flange sub-assembly (front side) onto the drive sprocket sub-assembly.

  1. Using SST to hold the companion flange, install a new companion flange lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }

  1. Using a chisel and hammer, stake the companion flange lock nut.



3. INSTALL PROPELLER SHAFT ASSEMBLY FRONT


C098708E03
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



4. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY (for 1GR-FE)


F052217
  1. Install the propeller shaft heat insulator bracket with the 2 bolts.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



5. INSTALL EXHAUST FRONT PIPE ASSEMBLY NO. 2 (for 1GR-FE)
  1. Install a new gasket onto the exhaust manifold LH.

  1. Install a new gasket onto the exhaust front pipe.

  1. Install the exhaust front pipe No. 2 onto the insulator.

  1. Install the exhaust front pipe No. 2 onto the exhaust manifold LH with the new 2 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }

  1. Install the exhaust front pipe No. 2 onto the exhaust front pipe with the 2 bolts and 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



    G036129E02
  1. Install a new gasket onto the exhaust front pipe No. 2.

    1. Using a wooden block and plastic- faced hammer, tap in a new gasket until it is flush with the exhaust front pipe No. 2.

      NOTICE:
      1. Make sure that the gasket is in the correct direction when installing.
      2. Do not reuse the removed gasket.



6. ADD TRANSFER OIL


7. INSPECT TRANSFER OIL


C083746E02
  1. Remove the filler plug and gasket.

  1. Check that the oil level is within 5 mm (0.20 in.) of the bottom of the filler plug hole.

    NOTICE:
    1. When replacing the oil, recheck the oil level after driving.
    2. Excessively large or small quantities of oil may cause troubles.

  1. When the oil level is too low, check for oil leakage.

  1. Tighten the filler plug with a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for 1GR-FE)

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



9. CHECK FOR EXHAUST GAS LEAKAGE


10. CHECK FRO TRANSFER OIL LEAKAGE