Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › COMPRESSOR AND MAGNETIC CLUTCH

COMPRESSOR AND MAGNETIC CLUTCH > INSTALLATION

for Preparation Click here



1. ADJUST COMPRESSOR OIL
  1. When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas from the service valve, drain the following volume of oil from new compressor and magnetic clutch before installation.

    Standard:
    (Oil capacity inside a new compressor and magnetic clutch: 150 + 15 cc (5.1 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed when replacing the compressor)

    NOTICE:
    1. When checking the compressor oil level, observe the precautions on the cooler removal/installation.
    2. If a new compressor and magnetic clutch are installed without removing some oil remaining in the pipes of the vehicle, the oil amount becomes too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.
    3. If the volume of oil remaining in the removed compressor and magnetic clutch is too small, check for oil leakage.
    4. Be sure to use RL-897 for compressor oil.



2. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (for 2TR-FE)


I045443E01
  1. Provisionally tighten the compressor and magnetic clutch with the 4 bolts and harness bracket.

    NOTICE:
    The harness bracket stopper should be in contact with compressor case.

  1. Tighten the compressor and magnetic clutch with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    NOTICE:
    Tighten the bolts in the sequence order shown in the illustration to install the compressor and magnetic clutch.

  1. Connect the connector.



3. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (for 1GR-FE)


I045442E01
  1. Provisionally tighten the compressor and magnetic clutch with the 4 bolts.

  1. Tighten the compressor and magnetic clutch with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

    NOTICE:
    Tighten the bolts in the sequence order shown in the illustration to install the compressor and magnetic clutch.

  1. Connect the connector.



4. INSTALL DISCHARGE HOSE SUB-ASSEMBLY


I045081E01
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new seal washer and fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    RL-897 or equivalent

  1. Install the seal washer onto the cooler refrigerant discharge hose sub-assembly.

  1. Install the cooler refrigerant discharge hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



5. INSTALL SUCTION HOSE SUB-ASSEMBLY (for 2TR-FE)


I045080E01
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new seal washer and fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    RL-897 or equivalent

  1. Install the seal washer onto the suction hose sub-assembly.

  1. Install the suction hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the suction hose sub-assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



6. INSTALL SUCTION HOSE SUB-ASSEMBLY (for 1GR-FE)


I045079E01
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new seal washer and fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    RL-897 or equivalent

  1. Install the seal washer onto the suction hose sub-assembly.

  1. Install the suction hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the suction hose sub-assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



7. INSTALL FRONT FENDER APRON SEAL UPPER


I045421E01
  1. Install the front fender apron seal upper with the 5 clips. (4WD, PRE RUNNER)



    I045441E01
  1. Install the front fender apron seal upper with the 6 clips. (2WD)



8. INSTALL GENERATOR ASSEMBLY (for 1GR-FE)
  1. Install the generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the wire harness clamp bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the wire harness.

    1. Connect the wire harness to terminal B and install the nut.

      Torque:
      9.8 N*m{ 100 kgf*cm , 7.0 ft.*lbf }

    2. Connect the connector to the generator assembly.

    3. Install the wire harness stay with the bolt.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



9. INSTALL FAN AND GENERATOR V BELT (for 2TR-FE)


G038204E01
  1. Provisionally install the V belt onto each pulley.

    NOTICE:
    Install the V belt onto each pulley and finally install the V belt onto the V-ribbed belt tensioner.

  1. Turn the hexagonal bolt on the V-ribbed belt tensioner clockwise and install the V belt onto the V-ribbed belt tensioner pulley.



10. INSPECT FAN AND GENERATOR V BELT (for 2TR-FE)


A095340E01
  1. Visually check the belt for excessive wear, frayed cords, etc..

    1. If any defects are found, replace the V-ribbed belt.
    2. Cracks on the rib side of the belt are considered acceptable. If the belt has chunks missing from the ribs, it should be replaced.



    A097753E02
  1. Check that the tensioner indicator mark is within range A shown in the illustration. If the mark is not within range A, replace the V belt.



11. INSTALL FAN AND GENERATOR V BELT (for 1GR-FE)


A076442E02
  1. While turning the belt tensioner counterclockwise, align with its holes, and then insert a bar of 6 mm (0.24 in.) into the holes to fix the belt tensioner.

  1. Install the V-ribbed belt.

  1. While turning the belt tensioner counterclockwise, remove the bar.



    A076443E01
  1. If it is hard to install the V-ribbed belt, perform the following procedure.

    1. Put the V-ribbed belt on all parts except the P/S pump, as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the P/S pump.



12. INSTALL FAN SHROUD (for 1GR-FE)


G036144E01
  1. Provisionally install the fan shroud together with the fan pulley.

  1. Install the fan and generator V belt .

  1. Install the fan pulley with the 4 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the 2 cooler hoses into the clamp (with automatic transmission).

  1. Connect the hose to the radiator reserve tank.



13. INSTALL RADIATOR SUPPORT TO FRAME SEAL LH (for 1GR-FE)


14. INSTALL V-BANK COVER (for 1GR-FE)
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



15. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for 2TR-FE)
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



16. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for 1GR-FE)
  1. Install the engine under cover with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



17. INSTALL FRONT WHEEL LH

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



19. CHARGE REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    570 to 630 g (20.10 to 22.22 oz.)

    SST
    07110-58060   (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor does not work properly without any refrigerant. This could cause the compressor to overheat.

    I040570E03



20. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2,000 rpm for 2 minutes or more after charging it with refrigerant.



21. CHECK FOR REFRIGERANT LEAKAGE
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the gas leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)



    I045073E01
  1. Using a gas leak detector, check the refrigerant line for leakage.



    I045074E01
  1. Bring the gas leak detector close to the drain hose with the detector power off.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Place the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to the volatile gases.
    If such reaction is unavoidable, the vehicle must be lifted up.

  1. If a gas leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.