POWER POINT SOCKET > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
![]() |
Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.
| 3. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
![]() |
Disengage the 4 clips and remove the instrument panel hole cover.
| 4. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type) |
![]() |
Remove the shift knob.
Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.
| 5. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type) |
![]() |
Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.
| 6. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
![]() |
Remove the console box carpet.
![]() |
Remove the 2 screws <F> and 2 bolts <B>.
Disengage the 4 claws and remove the rear console box assembly.
| 7. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) |
![]() |
Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.
| 8. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type) |
![]() |
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 9. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type) |
![]() |
Remove the shift knob.
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 10. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 11. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 12. REMOVE AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Using a screwdriver, disengage the 4 clips and remove the air conditioner control assembly.
Disconnect the 2 connectors.
| 13. REMOVE RADIO RECEIVER ASSEMBLY |
![]() |
Remove the 4 bolts.
Disconnect the connector and remove the radio receiver assembly with bracket.
| 14. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 2 claws.
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.
| 15. REMOVE NO. 1 LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Remove the 2 bolts <B>.
Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.
Disconnect the connectors.
| 16. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.
Disconnect the connectors.
| 17. REMOVE INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.
| 18. REMOVE LOWER INSTRUMENT PANEL LH |
![]() |
Remove the 3 bolts <B> and the lower instrument panel LH.
| 19. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY |
![]() |
Remove the bolt <B>.
Disengage the 5 clips and remove the instrument lower cover sub-assembly.
Disconnect the 2 connectors.
| 20. REMOVE POWER POINT SOCKET ASSEMBLY |
![]() |
Turn the socket counterclockwise as shown in the illustration, disengage the claw between the socket and the power point socket cover, and push the socket out towards the room side.
![]() |
Align the socket with the notch on the power point socket cover, and remove the power point socket assembly on the room side.