Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > INSTALLATION

for Preparation Click here



1. INSTALL RADIO ANTENNA CORD SUB-ASSEMBLY



E075961E01

  1. Engage the 4 claws and install the Radio antenna cord.



2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY


3. INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
  1. Install the instrument panel sub-assembly w/ passenger air bag assembly with the 8 bolts and nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the 5 clamps and connect the 4 connectors.



  1. Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.


    B085804E01



4. CONNECT PASSENGER AIRBAG CONNECTOR


    F050426E02
  1. Connect the passenger airbag connector and clamp.



5. INSTALL INSTRUMENT SIDE PANEL RH


    B085791E01
  1. Engage the 3 claws and install the instrument side RH.



6. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY


    B085789E01
  1. Connect the 2 connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



7. INSTALL LOWER INSTRUMENT PANEL LH


    B085788E01
  1. Install the lower instrument panel LH with the 3 bolts <B>.



8. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH


    B085787E01
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



9. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B085815E01
  1. Install the glow compartment door assembly with 3 hinges, holding it horizontal.



    B085785E01
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stopper onto the glove compartment door.



10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B085784E01
  1. Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.



11. INSTALL COMBINATION METER ASSEMBLY


B085782E01
  1. Connect the 2 connectors.

  1. Install the combination meter assembly with the 4 screws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



12. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B085781E01
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



13. INSTALL NO. 1 LOWER INSTRUMENT PANEL FINISH PANEL


B085780E01
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



14. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



15. INSTALL RADIO RECEIVER ASSEMBLY


E075957
  1. Connect the connector.

  1. Install the radio receiver assembly with bracket with the 4 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



16. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    B085779E01
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



17. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)


B085776E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085775E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



18. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)


    B085812E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085811E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



19. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    B085814E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



20. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)


    B085777E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.



21. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)


    B085773E01
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.



22. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



23. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Engage the 4 clips and claw, and remove the console upper panel sub-assembly.



24. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085769E01
  1. Engage the 6 clips and claw, and remove the console upper rear panel.

  1. Install the shift knob.



25. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)


    B085767E01
  1. Engage the 4 clips and install the instrument panel hole cover.



26. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)


    B085766E01
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



27. INSTALL FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



28. INSTALL FRONT PILLAR GARNISH LH


    B087596E01
  1. for LH Side:

    1. Install the 3 wire harness clamps.



    B087444E01
  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.



29. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip.



30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B087414E01
  1. Install the rear door opening trim weatherstrip.



31. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



32. INSTALL COWL SIDE TRIM BOARD LH


    B087438E01
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



33. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



34. INSTALL FRONT DOOR SCUFF PLATE LH


    B087476E01
  1. Engage the 8 claws and clip, and install the front door scuff plate.



35. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



36. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }