Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT (for 4WD)

FRONT DRIVE SHAFT (for 4WD) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT AXLE HUB OIL SEAL


C034792
  1. Using a screwdriver and a hammer, install a new oil seal.

    NOTICE:
    Do not damage the oil seal.



2. INSTALL FRONT DRIVE SHAFT DUST COVER


F041033E01
  1. Using SST and a press, install a new dust cover.

    SST
    09527-10011  



3. INSTALL FRONT DRIVE INNER SHAFT OUTER SHAFT SNAP RING
  1. Install a new snap ring.



4. INSTALL OUTBOARD JOINT BOOT


F052125E01

HINT:
  1. Before installing the boots, wrap the spline of the outboard joint with vinyl tape to prevent the boots from being damaged.
  2. Before installing the boot, place 2 new boot clamps on the small boot end and large boot ends.

  1. Provisionally install a new outboard joint boot with 2 new clamps onto the outboard joint shaft.

  1. Fill the outboard joint and boot with grease in the boot kit.

    Grease capacity:
    260 to 280 g (9.2 to 9.9 oz.)

  1. Provisionally install the boot onto the outboard joint.



5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP


F052126E01
  1. Install the boot clamps onto the boot.

  1. Place SST onto the large boot clamp.

    SST
    09521-24010  

  1. Tighten the SST so that the large boot clamp is pinched.

    NOTICE:
    Do not overtighten the SST.



    F052127E01
  1. Using SST, adjust the clearance of the large boot clamp.

    SST
    09240-00020  

    Clearance:
    1.0 to 5.0 mm (0.039 to 0.197 in.)

  1. Use the same procedure for the small boot clamp.



6. INSTALL INBOARD JOINT BOOT

HINT:
Before installing the boot, place a new boot clamp on the small boot end.

  1. Provisionally install a new inboard joint boot with a new clamp onto the outboard joint shaft.



7. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY


C067417E02
  1. Place the beveled side of the tripod toward the inboard joint.

  1. Align the matchmarks and install the tripod into the inboard joint.

  1. Using a brass bar and hammer, tap the tripod into the outboard joint shaft.

    NOTICE:
    Do not tap the roller.



    G022501
  1. Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint and boot with grease from the boot kit.

    Grease capacity:
    182 to 202 g (6.4 to 7.1 oz.)

  1. Align the matchmarks placed before removal and install the inboard joint onto the outboard joint shaft.

  1. Provisionally install the boot onto the inboard joint.



8. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
  1. Place the large boot clamp.



    F052128
  1. Using pliers, compress the large clamp and attach the claws.



    F052151E01
  1. Secure the boot clamp onto the boot.

  1. Place SST onto the small boot clamp.

    SST
    09521-24010  

  1. Tighten the SST so that the small boot clamp is pinched.

    NOTICE:
    Do not overtighten the SST.



    F052152E01
  1. Using SST, adjust the clearance of the small boot clamp.

    SST
    09240-00020  

    Clearance:
    1.0 to 4.0 mm (0.039 to 0.157 in.)



9. INSPECT FRONT DRIVE SHAFT


F052122
  1. Check whether there is no remarkable play in the outboard joint.

  1. Check whether the inboard joint slides smoothly in the thrust direction.

  1. Check whether there is no remarkable play in the radial direction of the inboard joint.

  1. Check the boots for damage.

    NOTICE:
    Move the drive shaft while keeping it level.



    F052216E01
  1. Make sure that the boots are not stretched or contracted when the drive shaft is at standard length.

    Drive shaft standard length:
    484.4 to 488.4 mm (19.071 to 19.226 in.)

    NOTICE:
    Move the drive shaft keeping it level.