Home › SUSPENSION & AXLE › AXLE › REAR AXLE HUB BOLT

REAR AXLE HUB BOLT > INSTALLATION

for Preparation Click here



1. INSTALL REAR AXLE HUB BOLT


C114966E01
  1. Install a new hub bolt through the axle hub.

  1. Install the washer plate, as shown in the illustration, through the hub bolt, and install the hub bolt by tightening the hub nut.



2. APPLY HIGH TEMPERATURE GREASE


F050548
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



3. INSTALL REAR BRAKE SHOE


F050549
  1. Apply high temperature grease to the adjusting bolt.



    F050550
  1. Install the parking brake shoe lever LH and parking brake shoe strut set with the shoe return spring onto the rear brake shoe.



    F050544
  1. Using pliers, install the parking brake shoe strut set, parking brake reaction lever and parking brake shoe lever LH with 2 new C-washers.



    F042688
  1. Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.



    F050543E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



4. INSTALL FRONT BRAKE SHOE
  1. Install the automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut lower onto the front brake shoe.



    F050542E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



    F042698
  1. Install the tension spring onto the front brake shoe and rear brake shoe.



    F050551
  1. Using needle-nose pliers, install the return spring.



    F050540E01
  1. Using SST, install the shoe return spring onto the front brake shoe.

    SST
    09921-00010  



5. INSPECT REAR DRUM BRAKE INSTALLATION


  1. Check that each part is installed properly.


    F050552E01



    F050553E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameters is the specified shoe clearance.

    Shoe clearance:
    0.5 mm (0.020 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



6. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Install a new drum gasket onto the rear brake drum.

  1. Install the rear brake drum.



7. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E02
  1. Provisionally install the hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 15 notches.

  1. Install the hole plug.



8. INSTALL REAR WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



9. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.

    Parking brake pedal travel at 300 N (31 kgf, 67 lbf):
    7 to 10 clicks



10. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    7 to 10 clicks



11. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Confirm that the parking brake pedal is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake pedal travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.



12. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Confirm that the parking brake lever is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake lever travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the parking brake lever indicator light comes on.