HEADLIGHT ASSEMBLY > REPAIR |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE RADIATOR GRILLE |
![]() |
Remove the 2 screws.
Using a clip remover, remove the 2 clips.
Disengage the 2 clips and remove the radiator grille.
| 3. REMOVE FRONT BUMPER COVER |
![]() |
Apply protective tape to the outer circumference of the front bumper cover, as shown in the illustration.
Remove the 6 screws.
Using a clip remover, remove the 7 clips.
Remove the 2 clips.
![]() |
w/ Fog Light:
Disconnect the 2 fog light connectors.
Disengage the 2 claws and remove the front bumper cover.
![]() |
Remove the 6 clips.
| 4. REMOVE FRONT BUMPER FILLER |
![]() |
Using a clip remover, remove the clip
Disengage the 2 claws and remove the front bumper filler.
| 5. REMOVE HEADLIGHT ASSEMBLY |
![]() |
Remove the bolt and 3 screws.
Disconnect the 3 connectors, then remove the LH headlight assembly.
| 6. INSTALL HEADLIGHT PROTECTOR UPPER RETAINER |
![]() |
Cut off the portion indicated by the shaded portion in the illustration and smooth the surface with sandpaper.
![]() |
Install the headlight protector upper retainer LH with the 2 screws.
| 7. INSTALL HEADLIGHT PROTECTOR LOWER RETAINER |
![]() |
Cut off the portion indicated by the shaded portion in the illustration and smooth the surface with sandpaper.
![]() |
Install the headlight protector lower retainer LH with the 2 screws.
| 8. INSTALL HEADLIGHT LOWER BRACKET |
![]() |
Cut off the portion indicated by the shaded portion in the illustration and smooth the surface with sandpaper.
![]() |
Install the headlight lower bracket LH with the 2 screws.
| 9. INSTALL HEADLIGHT ASSEMBLY |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 11. INSTALL FRONT BUMPER FILLER |
![]() |
Engage the 2 claws and install the front bumper filler.
Install the clip.
| 12. INSTALL FRONT BUMPER COVER |
![]() |
Install the 6 clips.
![]() |
Engage the 2 claws and install the front bumper cover.
Connect the 2 fog lamp connectors (w/ fog lamp).
![]() |
Install the 9 clips.
Tighten the 6 screws.
| 13. INSTALL RADIATOR GRILLE |
![]() |
Engage the 2 clips and install the radiator grille.
Install the 2 clips.
Tighten the 2 screws.
| 14. VEHICLE PREPARATION FOR HEADLIGHT AIM ADJUSTMENT |
Prepare the vehicle:
| 15. PREPARE FOR HEADLIGHT AIMING (for Using a Tester) |
Prepare the vehicle for headlight aim check.
Perform adjustment in accordance with the headlight tester instructions.
| 16. PREPARE FOR HEADLIGHT AIMING (for Using a Screen) |
Prepare the vehicle according to the following conditions:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.
Draw a vertical line down the center of screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).
| 17. HEADLIGHT AIMING INSPECTION |
Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight not being inspected from affecting headlight aiming inspection.
Start the engine.
Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.

| 18. HEADLIGHT AIMING ADJUSTMENT |
![]() |
Adjust the aim vertically:
Adjust the headlight aim into the specified range by turning aiming screw A with a screwdriver.
Perform low-beam aim adjustment.
![]() |
Adjust the aim horizontally:
Adjust the headlight aim into the specified range by turning aiming screw B with a screwdriver.