Home › BRAKE › BRAKE CONTROL › DECELERATION SENSOR (for 4WD and Pre-Runner without VSC)

DECELERATION SENSOR (for 4WD and Pre-Runner without VSC) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Bench Seat Type)


    B121777
  1. Slide the front seat to the most forward position.

  1. Disengage the hook.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the wiring harness clamp.

  1. Remove the wiring harness clamp.

  1. Remove the bolt and the front seat inner belt.



3. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Bench Seat Type)


    B121778
  1. Slide the front seat to the most forward position.

  1. Disengage the hook.

  1. Disconnect the connector.

  1. Using a clip remover, remove the wiring harness clamp.

  1. Remove the wiring harness clamp.

  1. Remove the bolt and the front seat inner belt.



4. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Bench Seat Type)


    B121738E01
  1. Push in the 2 lock buttons of the 2 front seat headrest supports and remove the 2 front seat headrests.



5. REMOVE FRONT SEAT ASSEMBLY (for Bench Seat Type)


    B121739
  1. Remove the belt of the front center seat outer belt from the front center seat outer belt guide.



    B121740
  1. Disconnect the 3 connectors.

  1. Using a clip remover, remove the 2 wiring harness clamps.



    B121741
  1. Remove the 4 bolts and the front seat.



6. REMOVE SEAT TRACK COVER (for Separate Seat Type)


B087374E01

HINT:
Follow the same procedures as for the opposite side.

  1. Disengage the 2 claws and remove the seat track cover.



7. REMOVE FRONT SEAT ASSEMBLY (for Separate Seat Type)


    B087646E01
  1. Disconnect the 2 connectors.

  1. w/ Front Seat Side Airbag:

    1. Disconnect the connector.

  1. Using a clip remover, remove the wire harness clamp.



    B087375E01
  1. Remove the 4 bolts and front seat.



8. REMOVE FRONT FLOOR FOOTREST


    B087437E01
  1. Disengage the 2 clips and remove the front floor footrest.



9. REMOVE FRONT DOOR SCUFF PLATE (for Regular Cab)


    B087476E01
  1. Disengage the 8 claws and clip, and remove the front door scuff plate.



10. REMOVE FRONT DOOR SCUFF PLATE (for Access Cab)


    B087476E01
  1. Disengage the 8 claws and clip, and remove the front door scuff plate.



11. REMOVE FRONT DOOR SCUFF PLATE (for Double Cab)


    B087411E01
  1. Disengage the 9 claws and remove the front door scuff plate.



12. REMOVE COWL SIDE TRIM BOARD (for Regular Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



13. REMOVE COWL SIDE TRIM BOARD (for Access Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



14. REMOVE COWL SIDE TRIM BOARD (for Double Cab)


    B087438E01
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim board.



15. REMOVE SENSOR BRACKET
  1. Turn up the floor carpet.



    F050580
  1. Remove the wire harness clamp.

  1. Remove the bolt and bracket.



16. REMOVE DECELERATION SENSOR


F050582
  1. Disconnect the deceleration sensor connector.

  1. Remove the 2 bolts and deceleration sensor.