BRAKE PEDAL > INSTALLATION |
| 1. INSTALL BRAKE PEDAL PAD |
Install the brake pedal pad onto the brake pedal.
| 2. INSTALL BRAKE PEDAL LEVER |
Apply lithium soap base glycol grease to the 2 brake pedal link pins, 2 pedal shaft collars and 2 brake pedal links.
Install the brake pedal lever with the 2 brake pedal link pins, 2 brake pedal shaft collars and 2 brake pedal links onto the brake pedal.
Install 2 new E-rings onto each brake pedal link pin.
| 3. INSTALL BRAKE PEDAL |
Apply lithium soap base glycol grease to the 2 collars and 4 brake pedal bushes.
Install the 2 collars and 4 brake pedal bushes onto the brake pedal and brake pedal lever.
![]() |
Install the brake pedal with the bolt and nut onto the brake pedal support.
| 4. INSTALL STOP LIGHT SWITCH ASSEMBLY |
![]() |
Insert the stop light switch until the body comes into contact with the cushion.
![]() |
Make a quarter turn clockwise to install the stop light switch.
Check the protrusion of the rod.
| 5. INSTALL BRAKE PEDAL RETURN SPRING |
Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal support and brake pedal.
Install the return spring onto the brake pedal support and brake pedal.
| 6. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
![]() |
Install the 4 nuts and brake pedal support.
Connect the stop light switch connector to the stop lamp switch.
| 7. INSTALL BRAKE PEDAL SUPPORT REINFORCEMENT |
Install the reinforcement onto the brake pedal support.
![]() |
Provisionally tighten the bolt and nut to the brake pedal support, reinforcement and brake pedal lever.
![]() |
Install the bolt onto the reinforcement.
Tighten the bolt and nut.
| 8. INSTALL MASTER CYLINDER PUSH ROD CLEVIS |
Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.
Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.
| 9. INSPECT BRAKE PEDAL HEIGHT |
![]() |
Check the brake pedal height.
![]() |
Adjust the rod operating adapter length.
Remove the clip and clevis pin.
Loosen the clevis lock nut.
Adjust the rod operating adapter length by turning the pedal push rod clevis.
Tighten the clevis lock nut.
Install the clip and clevis pin.
| 10. INSPECT PEDAL FREE PLAY |
![]() |
Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.
Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.
| 11. INSPECT PEDAL RESERVE DISTANCE |
![]() |
Release the parking brake pedal.
With the engine running, depress the pedal and measure the pedal reserve distance as shown.
| 12. INSTALL DRIVER SIDE JUNCTION BLOCK |
| 13. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER NO. 1 |
![]() |
Connect the connectors.
Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.
Install the 2 bolts <B>.
| 14. INSTALL INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission) |
![]() |
Engage the 4 clips and 2 claws, and install the instrument panel under tray.
| 15. INSTALL INSTRUMENT PANEL HOLE COVER (for Manual Transmission) |
![]() |
Engage the 4 clips and install the instrument panel hole cover.
| 16. INSTALL COWL SIDE TRIM BOARD (for Regular Cab) |
![]() |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 17. INSTALL COWL SIDE TRIM BOARD (for Access Cab) |
![]() |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 18. INSTALL COWL SIDE TRIM BOARD (for Double Cab) |
![]() |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 19. INSTALL FRONT DOOR SCUFF PLATE (for Regular Cab) |
![]() |
Engage the 8 claws and clip, and install the front door scuff plate.
| 20. INSTALL FRONT DOOR SCUFF PLATE (for Access Cab) |
![]() |
Engage the 9 claws and clip, and install the front door scuff plate.
| 21. INSTALL FRONT DOOR SCUFF PLATE (for Double Cab) |
![]() |
Engage the 9 claws and install the front door scuff plate.
| 22. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 clips and install the front floor footrest.
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |