Home › BRAKE › BRAKE › FRONT BRAKE (for 2WD)

FRONT BRAKE (for 2WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DISC
  1. Aligning the matchmarks, install the front disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



2. INSPECT DISC RUNOUT


F051230
  1. Provisionally fasten the disc with the hub nuts.

    Torque:
    113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }

  1. Using a dial indicator, measure the disc runout 10 mm (0.39 in.) away from the outer edge of the disc.

    Maximum disc runout:
    0.05 mm (0.0020 in.)

  1. If the disc runout is the maximum value or greater, check the bearing play in the axial direction and check the axle hub runout . If the bearing play and axle hub runout are normal, adjust the disc runout or grind it on an on-car brake lathe.



3. INSTALL FRONT DISC BRAKE BUSH DUST BOOT


F051233
  1. Place soft jaws on a vise and hold the disc brake cylinder mounting in the vise through aluminum plates.

  1. Apply lithium soap base glycol grease to the sealing surface of 2 new front disc brake bush dust boots.

  1. Using a socket wrench (19 mm) and hammer, tap the 2 disc brake bush dust boots into the disc brake cylinder mounting.



4. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING


F051225
  1. Install the disc brake cylinder mounting with the 2 bolts.

    Torque:
    108 N*m{ 1,101 kgf*cm , 80 ft.*lbf }



5. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH
  1. Apply lithium soap base glycol grease to a new disc brake cylinder slide bush.

  1. Install the disc brake cylinder slide bush to the bottom side of the disc brake cylinder slide pin (No. 2).



6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


F051224E02
  1. Apply lithium soap base glycol grease to the sliding part and the sealing surface of the disc brake cylinder slide pin.

  1. Install the disc brake cylinder slide pin onto the disc brake cylinder mounting.



7. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
  1. Install the 2 disc brake pad support plates onto the disc brake cylinder mounting.



8. INSTALL ANTI SQUEAL SHIM KIT FRONT

NOTICE:
If necessary, replace the anti-squeal shim kit when replacing the brake pad.

  1. Apply disc brake grease to the both surfaces of the 2 anti-squeal shims and install them.

  1. Install the 2 outside anti-squeal shims onto the brake pads.

  1. Install the pad wear indicator plate facing upward, and install each pad.



9. INSTALL DISC BRAKE PAD KIT FRONT (PAD ONLY)
  1. Install the 2 disc brake pads with anti-squeal shim onto the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the brake pads or the front disc.



10. INSTALL DISC BRAKE CYLINDER ASSEMBLY


F051222
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    36.3 N*m{ 370 kgf*cm , 27 ft.*lbf }



    F050588
  1. Install a new gasket and flexible hose with the union bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



11. FILL RESERVOIR WITH BRAKE FLUID (w/ VSC)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



12. FILL RESERVOIR WITH BRAKE FLUID (w/o VSC)


F050555

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



13. BLEED MASTER CYLINDER (w/o VSC)


F050556

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. Using SST, disconnect the brake lines from the master cylinder.

    SST
    09023-00101  

  1. Slowly depress the brake pedal and hold it there (step A).



    F050557
  1. Block the outer holes with your fingers, and release the brake pedal (step B).

  1. Repeat step A and B 3 or 4 times.



14. BLEED BRAKE LINE (w/ VSC)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



15. BLEED BRAKE LINE (w/o VSC)


F050558
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step D).

  1. Repeat step C and D until all the air in the fluid has been bled out.

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



16. CHECK FLUID LEVEL IN RESERVOIR (w/ VSC)
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).



17. CHECK FLUID LEVEL IN RESERVOIR (w/o VSC)
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS NO. 116 DOT3



18. CHECK FOR BRAKE FLUID LEAKAGE


19. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }