Home › BRAKE › PARKING BRAKE › PARKING BRAKE SYSTEM

PARKING BRAKE SYSTEM > ADJUSTMENT

for Preparation Click here



1. REMOVE REAR WHEEL


2. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E02
  1. Provisionally install the hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 15 notches.

  1. Install the hole plug.



3. INSTALL REAR WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



4. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.

    Parking brake pedal travel at 300 N (31 kgf, 67 lbf):
    7 to 10 clicks



5. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    7 to 10 clicks



6. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085768E01
  1. Remove the shift knob.

  1. Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.



7. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



8. REMOVE CONSOLE BOX ASSEMBLY REAR (for Separate Seat Type)


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



9. REMOVE PARKING BRAKE CABLE JOINT PROTECTOR (for Bench Seat Type)
  1. Slide the seat to the rearmost position.

  1. Pull up the floor carpet around the cable joint protector, along its seams.



    F050698
  1. Remove the 3 bolts and parking brake cable joint protector.



10. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Confirm that the parking brake pedal is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake pedal travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.



11. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Confirm that the parking brake lever is released.



    F050697E01
  1. Loosen the lock nut A and turn the adjusting nut B until the parking brake lever travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the parking brake lever indicator light comes on.



12. INSTALL PARKING BRAKE CABLE JOINT PROTECTOR (for Bench Seat Type)


F050698
  1. Install the 3 bolts and parking brake cable joint protector.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Return the floor carpet to its original position.

  1. Return the seat to its original position.



13. INSTALL CONSOLE BOX ASSEMBLY REAR (for Separate Seat Type)


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



14. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B085769E01
  1. Engage the 6 clips and claw, and remove the console upper rear panel.

  1. Install the shift knob.



15. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)


    B085770E01
  1. Engage the 4 clips and claw, and remove the console upper panel sub-assembly.