POWER STEERING LINK (for 2WD) > REASSEMBLY |
| 1. INSTALL RACK STEERING PISTON RING |
![]() |
Coat a new O-ring with power steering fluid and install it onto the power steering rack.
Expand a new piston ring with your fingers.
Coat a new piston ring with power steering fluid.
![]() |
Install the piston ring onto the power steering rack, and position it with your fingers.
| 2. INSTALL POWER STEERING CYLINDER TUBE OIL SEAL |
Coat a new cylinder tube oil seal lip with power steering fluid.
![]() |
Using SST and a press, install the cylinder tube oil seal.
| 3. INSTALL POWER STEERING RACK |
![]() |
Install SST onto the power steering rack.
Coat SST with power steering fluid.
Install the power steering rack into the rack housing.
Remove SST.
| 4. INSTALL POWER STEERING RACK BUSH |
![]() |
Using SST and a press, install a new rack bush oil seal onto the rack bush.
Coat a new O-ring with power steering fluid and install it onto the rack bush.
![]() |
To prevent the rack bush oil seal lip from being damaged, wind vinyl tape around the rack end and apply power steering fluid.
Install the rack bush onto the power steering rack.
| 5. INSTALL CYLINDER END STOPPER |
![]() |
Align the installation hole for the wire of the cylinder end stopper with the slot of the rack housing.
Install a new wire into the cylinder end stopper.
Using a screwdriver, turn the cylinder end stopper clockwise by 400 to 500°.
| 6. AIR TIGHTNESS TEST |
![]() |
Install SST onto the rack housing.
Apply a vacuum of 53 kPa (400 mmHg, 15.75 in.Hg) for about 30 seconds.
Check that there is no change in the vacuum.
If there is any change in the vacuum, check whether the oil seals are installed correctly.
| 7. INSTALL POWER STEERING CONTROL VALVE UPPER OIL SEAL |
Coat the control valve upper bearing and a new control valve upper oil seal with power steering fluid.
![]() |
Using SST and a press, install the control valve upper oil seal.
![]() |
Using SST and a press, install the control valve upper bearing.
| 8. INSTALL POWER STEERING CONTROL VALVE ASSEMBLY |
![]() |
Expand 4 new control valve rings with your fingers.
Coat the 4 control valve rings with power steering fluid.
Install the 4 control valve rings onto the control valve, and position them with your fingers.
![]() |
Carefully slide the tapered end of SST over the control valve rings until they fit to the control valve.
![]() |
To prevent the control valve upper oil seal lip from getting damaged, wind vinyl tape around the serrated portion of the control valve.
Coat the control valve upper oil seal lip with power steering fluid.
Install the control valve onto the control valve housing.
Apply grease to the needle roller bearing.
Install a new O-ring onto the control valve housing.
Wind vinyl tape around the serrated portion of the control valve.
![]() |
Install the control valve w/ control valve housing onto the rack housing with the 2 bolts.
| 9. INSTALL STEERING GEAR RACK GUIDE |
Install the rack guide.
Install the rack guide spring.
Apply sealant to 2 or 3 threads of the rack guide spring cap.
Provisionally install the rack guide spring cap.
| 10. ADJUST TOTAL PRELOAD |
![]() |
To prevent the steering rack teeth from damaging the oil seal lip, provisionally install the RH and LH steering rack end.
Using SST, torque the rack guide spring cap.
![]() |
Using SST, loosen the rack guide spring cap.
![]() |
Using SST, turn the control valve to the right and left once or twice.
Using SST, loosen the rack guide spring cap until the rack guide spring ceases to function.
![]() |
Using SST and a torque wrench, tighten the rack guide spring cap until the preload is within the specification.
Apply sealant to 2 or 3 threads of the rack guide spring cap nut.
Provisionally install the rack guide spring cap nut.
![]() |
Using SST, hold the rack guide spring cap and using another SST, torque the rack guide spring cap nut.
Recheck the total preload.
Remove the RH and LH steering rack ends
![]() |
Apply MP grease to the control valve as shown in the illustration.
![]() |
Wind vinyl tape around the serrated portion of the control valve.
Install the dust cover onto the control valve housing.
| 11. INSTALL STEERING RACK END SUB-ASSEMBLY |
![]() |
Install 2 new claw washers, and provisionally install the 2 steering rack ends.
Using 2 SSTs, install the 2 steering rack ends.
![]() |
Using a brass bar and hammer, stake the 2 claw washers.
| 12. INSPECT STEERING RACK END SUB-ASSEMBLY |
![]() |
Ensure that the steering rack end hole is not clogged with grease.
| 13. INSTALL STEERING RACK BOOT NO. 1 |
| 14. INSTALL STEERING RACK BOOT NO. 2 |
| 15. INSTALL STEERING RACK BOOT NO. 1 CLAMP |
![]() |
Using SST, tighten the rack boot No. 1 clamp as shown in the illustration.
| 16. INSTALL STEERING RACK BOOT NO. 2 CLAMP |
| 17. INSTALL STEERING RACK BOOT CLIP |
Using pliers, install the 2 rack boot clips.
| 18. INSTALL TIE ROD END SUB-ASSEMBLY LH |
Screw the lock nut and tie rod end onto the rack end until the matchmarks are aligned.
After adjusting toe-in, torque the nut.
| 19. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 20. INSTALL STEERING TURN PRESSURE TUBE |
Coat 4 new O-rings with power steering fluid and install them onto the pressure tubes.
![]() |
Using SST, install the 2 pressure tubes.
| 21. REMOVE STEERING GEAR OUTLET RETURN TUBE |
![]() |
Using SST, install the return tube.