POWER STEERING LINK (for 4WD and Pre-Runner) > INSTALLATION |
| 1. INSTALL POWER STEERING LINK |
![]() |
Install the power steering link with the 2 bolts and 2 nuts.
| 2. INSTALL PRESSURE FEED TUBE ASSEMBLY |
![]() |
Connect the return hose with the clip.
![]() |
Using SST, tighten the flare nut and connect the pressure feed tube.
![]() |
for 2TR-FE:
Install the tube support bracket with the bolt.
![]() |
for 1GR-FE:
Install the tube support brackets with the 2 bolts.
| 3. INSTALL TIE ROD END SUB-ASSEMBLY LH |
Install the tie rod end onto the steering knuckle arm.
Install the nut.
Install a new cotter pin.
| 4. INSTALL TIE ROD END SUB-ASSEMBLY RH |
| 5. INSTALL STEERING INTERMEDIATE SHAFT NO. 2 |
![]() |
Align the matchmarks on the steering intermediate shaft No. 2 and power steering link.
Install the steering intermediate shaft No. 2 onto the power steering link with bolt C.
![]() |
Align the matchmarks on the steering intermediate shaft and steering sliding yoke.
Install the steering sliding yoke onto the steering intermediate shaft and slide it upward.
Align the matchmarks on the steering sliding yoke and steering intermediate shaft No. 2.
Install the steering sliding yoke with bolts A and B.
| 6. INSTALL FRONT STABILIZER BAR |
| 7. INSTALL FRONT STABILIZER BRACKET NO. 1 LH |
![]() |
Install the front stabilizer bracket with the 2 bolts.
| 8. INSTALL FRONT STABILIZER BRACKET NO. 1 RH |
| 9. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Connect the stabilizer link to the steering knuckle with the nut.
| 10. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 11. INSTALL FRAME CROSSMEMBER SUB-ASSEMBLY NO. 3 |
![]() |
Install the frame crossmember sub-assembly No. 3 with the 8 bolts and nuts.
Install the 4 bolts onto the engine mounting insulator rear No. 1.
| 12. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab Pre-Runner) |
![]() |
Remove SST from the extension housing.
Install the propeller shaft assembly into the extension housing.
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.
| 13. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab Pre-Runner) |
![]() |
Remove SST from the extension housing.
Install the propeller shaft into the extension housing.
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
![]() |
Provisionally install the center support bearing with the 2 mounting bolts.
![]() |
Adjust the center support bearing.
Torque the 2 bolts.
| 14. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab 4WD) |
![]() |
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft with the 4 nuts and 4 washers.
![]() |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
| 15. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab 4WD) |
![]() |
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft with the 4 nuts and 4 washers.
![]() |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
![]() |
Provisionally install the center support bearing with 2 mounting bolts.
Torque the 2 bolts.
| 16. INSTALL PROPELLER SHAFT ASSEMBLY FRONT (for 4WD) |
![]() |
Align the matchmarks on the yoke and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
![]() |
Align the matchmarks on the yoke and transfer flange.
Install the propeller shaft with the 4 nuts and 4 washers.
| 17. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for 2TR-FE) |
![]() |
Check the free length.
Using vernier calipers, measure the free length of the compression spring.
![]() |
Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the exhaust manifold.
Install the exhaust pipe front into the exhaust pipe support.
Tighten the 2 bolts and 2 compression springs.
| 18. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for 1GR-FE) |
Install a new gasket onto the exhaust manifold RH.
Install the exhaust front pipe with the new 2 nuts.
| 19. INSTALL EXHAUST FRONT PIPE ASSEMBLY NO. 2 (for 1GR-FE) |
Install a new gasket onto the exhaust manifold LH.
Install a new gasket onto the exhaust front pipe.
Install the exhaust front pipe No. 2 onto the insulator.
Install the exhaust front pipe No. 2 onto the exhaust manifold LH with the new 2 nuts.
Install the exhaust front pipe No. 2 onto the exhaust front pipe with the 2 bolts and 2 nuts.
![]() |
Install a new gasket onto the exhaust front pipe No. 2.
Using a wooden block and plastic- faced hammer, tap in a new gasket until it is flush with the exhaust front pipe No. 2.
| 20. INSTALL FRONT WHEELS |
| 21. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 22. INSPECT STEERING WHEEL CENTER POINT |
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 24. ADD POWER STEERING FLUID |
| 25. BLEED POWER STEERING FLUID |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).
Repeat step A several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.
Check the fluid level.
| 26. CHECK FOR POWER STEERING FLUID LEAKAGE |
| 27. CHECK FOR EXHAUST GAS LEAKAGE |
| 28. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 29. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO. 1 |