POWER STEERING LINK (for 4WD and Pre-Runner) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 3. REMOVE FRONT WHEELS |
| 4. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO. 1 |
| 5. REMOVE EXHAUST PIPE ASSEMBLY FRONT (for 2TR-FE) |
Remove the 2 bolts and 2 compression springs.
Remove the exhaust pipe front from the exhaust pipe support.
Remove the gasket from the exhaust manifold.
| 6. REMOVE EXHAUST FRONT PIPE ASSEMBLY NO. 2 (for 1GR-FE) |
Remove the 2 bolts and 2 nuts, then separate the exhaust front pipe No. 2 from the exhaust front pipe.
Remove the 2 nuts, then separate the exhaust front pipe No. 2 from the exhaust manifold LH.
Separate the insulator, then remove the exhaust front pipe No. 2.
| 7. REMOVE EXHAUST PIPE ASSEMBLY FRONT (for 1GR-FE) |
Remove the 2 nuts, then remove the exhaust front pipe.
| 8. REMOVE PROPELLER SHAFT ASSEMBLY FRONT (for 4WD) |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 9. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab Pre-Runner) |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Remove the propeller shaft.
Insert SST into the transmission to prevent oil leakage.
| 10. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab Pre-Runner) |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts and 4 washers, and remove the propeller shaft.
![]() |
Remove the 2 center support bearing bolts from the frame crossmember.
![]() |
Pull out the propeller shaft.
Insert SST into the transmission to prevent oil leakage.
| 11. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab 4WD) |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 12. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab 4WD) |
![]() |
Place matchmarks on the propeller shaft flange and differential.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Remove the 2 center support bearing bolts from the frame crossmember.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 13. REMOVE FRAME CROSSMEMBER SUB-ASSEMBLY NO. 3 |
![]() |
Support the transfer with a support stand.
![]() |
Remove the 4 bolts from the engine rear mounting.
Remove the 4 bolts, nuts and frame crossmember sub- assembly No. 3.
| 14. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and disconnect the stabilizer link from the steering knuckle.
| 15. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 16. REMOVE FRONT STABILIZER BRACKET NO. 1 LH |
![]() |
Remove the 2 bolts and front stabilizer bracket.
| 17. REMOVE FRONT STABILIZER BRACKET NO. 1 RH |
| 18. REMOVE FRONT STABILIZER BAR |
| 19. REMOVE STEERING INTERMEDIATE SHAFT NO. 2 |
![]() |
Fix the steering wheel with the seat belt in order to prevent it from rotating.
![]() |
Place matchmarks on the steering sliding yoke, steering intermediate shaft No. 2 and steering intermediate shaft.
Remove bolts A and B from the steering sliding yoke.
Slide the steering sliding yoke up and separate it from the steering intermediate shaft No. 2.
Pull down the steering sliding yoke from the steering intermediate shaft to remove it.
![]() |
Place matchmarks on the steering intermediate shaft No. 2 and power steering link.
Remove bolt C from the steering intermediate shaft No. 2.
Slide the steering intermediate shaft No. 2 up and remove it from the power steering link.
| 20. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and nut.
![]() |
Using SST, separate the tie rod end from the steering knuckle arm.
| 21. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
| 22. SEPARATE PRESSURE FEED TUBE ASSEMBLY |
![]() |
for 2TR-FE:
Remove the bolt and separate the tube support bracket.
![]() |
for 1GR-FE:
Remove the 2 bolts and separate the tube support brackets.
![]() |
Using SST, loosen the flare nut and separate the pressure feed tube.
![]() |
Disengage the clip and disconnect the return hose.
| 23. REMOVE POWER STEERING LINK |
![]() |
Remove the 2 bolts and 2 nuts.
Tilt the transmission and remove the power steering link.