Home › TRANSMISSION ยท CLUTCH › CLUTCH MASTER CYLINDER

CLUTCH MASTER CYLINDER > INSTALLATION

for Preparation Click here



1. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY


F050811
  1. Install the clutch master cylinder with the 2 bolts.

    Torque:
    16 N*m{ 158 kgf*cm , 11 ft.*lbf }

  1. Install the clutch start switch with the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



    F050809E01
  1. Using SST, connect the clutch master cylinder to 2 way tube.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

  1. Connect the clutch reservoir tube.



2. INSTALL CLUTCH PEDAL WITH CLUTCH MASTER CYLINDER


F050808
  1. Install the clutch pedal with clutch master cylinder onto the vehicle with the 2 nuts and bolt.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf } for nut
    24 N*m{ 245 kgf*cm , 18 ft.*lbf } for bolt

  1. Connect the clutch start switch connector.



3. CONNECT DRIVER SIDE JUNCTION BLOCK


4. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


B085780E01
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



5. INSTALL COWL SIDE TRIM BOARD LH


6. INSTALL FRONT DOOR SCUFF PLATE LH


7. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE


F050807E01
  1. Using SST, connect the flexible hose tube.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



8. CONNECT CLUTCH RESERVOIR TUBE


9. BLEED BRAKE LINE (w/o VSC)


10. BLEED CLUTCH PIPE LINE


11. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
  1. Lift the floor carpet.



    F050836E01
  1. Check that the pedal height is correct.

    Pedal height from asphalt sheet:
    168.5 to 178.5 mm (6.634 to 7.028 in.)

  1. Adjust the pedal height.

    1. Loosen the lock nut and turn the stopper bolt until the height is correct. Tighten the lock nut.

      Torque:
      25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Check that the pedal free play and push rod play are correct.

    1. Depress the pedal until the clutch resistance begins to be felt.

      Pedal free play:
      5.0 to 15.0 mm (0.197 to 0.591 in.)

    2. Gently depress the pedal until the resistance begins to increase a little.

      Push rod play at pedal top:
      1.0 to 5.0 mm (0.039 to 0.197 in.)



    D031462E03
  1. Adjust the pedal free play and push rod play.

    1. Loosen the lock nut and turn the push rod until the free play and push rod play are correct.

    2. Tighten the lock nut.

    3. After adjusting the pedal free play, check the pedal height.

    4. Connect the air duct and install the lower finish panel.



    CL00512E05
  1. Check the clutch release point.

    1. Pull the parking brake lever and use wheel chocks.

    2. Start the engine and allow it to idle.

    3. Without depressing the clutch pedal, slowly move the shift lever into the reverse position until the gears engage.

    4. Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

      Standard distance:
      25 mm (0.984 in.) or more
      (From pedal stroke end position to release point)

      If the distance is not as specified, perform the following operations.
      1. Check the pedal height.
      2. Check the push rod play and pedal free play.
      3. Bleed the clutch line.
      4. Check the clutch cover assembly and disc assembly.



12. CHECK BRAKE FLUID LEAKAGE (w/o VSC)


13. CHECK FOR CLUTCH FLUID LEAKAGE


14. CHECK FLUID LEVEL IN RESERVOIR