Home › TRANSMISSION ยท R155 MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Separate Seat Type)


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



3. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



4. REMOVE FRONT CONSOLE BOX (for Separate Seat Type)


    B085813E01
  1. Remove the shift knob.

  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



5. REMOVE FRONT CONSOLE BOX (for Bench Seat Type)


    B085774E01
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the instrument panel cup holder.

  1. Remove the No. 2 box bottom mat.



    B085776E01
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



6. REMOVE SHIFT LEVER BOOT ASSEMBLY


F050667E01
  1. Remove the 2 screws A, 2 clips B and floor shift lever assembly.



7. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY


G021695E03
  1. Cover the shift lever cap with a cloth.

  1. While pressing down on the shift lever, turn it counterclockwise to remove.

  1. Pull out the shift lever.



8. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and engine under cover No. 2.



9. DRAIN MANUAL TRANSMISSION OIL

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



10. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the exhaust pipe front from the exhaust pipe support.

  1. Remove the gasket from the exhaust manifold.



11. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Access Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and remove the propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    D033911E01
  1. Pull out the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



12. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    D033911E01
  1. Remove the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



13. REMOVE STARTER ASSEMBLY


G037949E01
  1. Remove the terminal cap.

  1. Remove the nut, then remove the starter wire harness.

  1. Disconnect the starter connector.



    G037950E01
  1. Remove the 2 bolts, then remove the starter.



14. REMOVE MANIFOLD STAY


F050668
  1. Remove the 3 bolts and manifold stay.



15. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY


G021426
  1. Remove the 2 bolts and separate the clutch release cylinder assembly.



16. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Support the transmission rear side with a transmission jack.



    G021429E01
  1. Remove the 4 bolts from the engine rear mounting.

  1. Remove the 4 bolts, nuts and flame crossmember sub-assembly No. 3.



17. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR


G021430
  1. Remove the 4 bolts and engine mounting insulator rear No. 1.



18. DISCONNECT WIRE HARNESS
  1. Tilt the transmission assembly downward.

    NOTICE:
    Make sure that the cooling fan does not come in contact with the fan shroud.

  1. Disconnect the back-up lamp switch connector.

  1. Disconnect the speed sensor connector.

  1. Disconnect the wire harness clamp from the transmission assembly.



19. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY


F050669
  1. Remove the 7 bolts and remove the transmission assembly.