Home › TRANSMISSION ยท R155 MANUAL TRANSMISSION › MANUAL TRANSMISSION UNIT

MANUAL TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE MANUAL TRANSMISSION FILLER PLUG


D029023
  1. Remove the transmission filler plug and gasket from the transmission case.



2. REMOVE DRAIN PLUG SUB-ASSEMBLY


D029024
  1. Remove the transmission drain plug and gasket from the transmission case.



3. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY


D029025
  1. Remove the clutch release fork and clutch release bearing from the clutch housing.



4. REMOVE CLUTCH RELEASE BEARING ASSEMBLY


D029026
  1. Remove the release bearing hub clip, and then remove the clutch release bearing from the clutch release fork.



5. REMOVE RELEASE FORK SUPPORT


D025933
  1. Remove the release fork support from the clutch housing.



6. REMOVE CLUTCH RELEASE FORK BOOT


D029027
  1. Remove the clutch release fork boot from the clutch housing.



7. REMOVE CLUTCH HOUSING


D029028
  1. Remove the 9 bolts.



    D029029
  1. Using a plastic hammer, remove the clutch housing from the transmission case.



8. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


D029030E01
  1. Using SST, remove the back-up light switch assembly and the gasket from the transmission case.

    SST
    09817-16011  



9. REMOVE SPEEDOMETER SENSOR
  1. Remove the bolt and speedometer sensor from the extension housing.

  1. Remove the O-ring from the speedometer sensor.



10. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY


F050654
  1. Remove the 6 bolts.

  1. Remove the floor shift control shift lever retainer gasket from the extension housing.

  1. Remove the control shift lever retainer gasket from the extension housing.



11. REMOVE REVERSE RESTRICT PIN


F050675
  1. Remove the 2 reverse restrict pins from the extension housing or transfer adapter.



12. REMOVE EXTENSION HOUSING SUB-ASSEMBLY


F050673
  1. Remove the shift lever housing set bolt from the shift lever housing.



    F050651
  1. Remove the 10 bolts.

  1. Using a plastic hammer, remove the extension housing, shift lever housing and shift and select lever.



13. REMOVE OIL RECEIVER


D029037
  1. Remove the oil receiver from the extension housing.



14. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE
  1. Remove the bolt and oil receiver pipe from the extension housing.



15. REMOVE REVERSE RESTRICT PIN ASSEMBLY
  1. Using a "Torx" socket wrench T40, remove the reverse restrict pin plug from the transfer adapter.



    F050672
  1. Using a pin punch (5 mm) and a hammer, remove the reverse restrict pin slotted from the transfer adapter or extension housing.



    D029042
  1. Remove the reverse restrict pin from the transfer adapter or extension housing.



16. REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL


D029043
  1. Using a screwdriver, remove the extension housing oil seal from the extension housing.



17. REMOVE FRONT BEARING RETAINER


D025950
  1. Remove the 8 bolts.



    D025951
  1. Using a brass bar and a hammer, remove the front bearing retainer from the transmission case.



18. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL


D025952E01
  1. Fix the front bearing retainer in a vise, between aluminum plate.

  1. Using SST, remove the transmission front bearing retainer oil seal.

    SST
    09308-00010  



19. REMOVE FRONT BEARING SHAFT SNAP RING


D025953
  1. Using a snap ring expander, remove the front bearing shaft snap ring from the transmission case.



20. REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING


D025954
  1. Using a snap ring expander, remove the counter gear front bearing snap ring No. 1 from the transmission case.



21. REMOVE MANUAL TRANSMISSION CASE


D029044
  1. Using a brass bar and a hammer, remove the transmission case from the intermediate plate.



22. REMOVE TRANSMISSION MAGNET


D025957
  1. Remove the transmission magnet from the intermediate plate.



23. FIX INTERMEDIATE PLATE


D029045
  1. Fix the intermediate plate in a vice between aluminum plates.



24. REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT


D029046
  1. Using a "Torx" socket wrench T40, remove the shift detent ball spring seat No. 1 from the intermediate plate.



    D025960
  1. Using a magnetic finger, remove the shift detent ball low side compression spring and the shift detent ball from the intermediate plate.



    D029047E01
  1. Using a "Torx" socket wrench T40, remove the 3 shift detent ball spring seats No. 1 from the intermediate plate.



    D025962
  1. Using a magnetic finger, remove the 2 shift detent ball low side compression springs and the 2 shift detent balls from the intermediate plate.



25. REMOVE NO. 2 GEAR SHIFT FORK SHAFT


D029048
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft snap ring from the gear shift fork shaft No. 2.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    D029049
  1. Remove the shift fork set bolt from the gear shift fork No. 2.



    D029050
  1. Remove the gear shift fork shaft No. 2 from the intermediate plate.



    D029051
  1. Remove the gear shift fork No. 2 from the transmission hub sleeve No. 2.



    D025967
  1. Using a magnetic finger, remove the shift interlock No. 1 roller and the shift interlock pin (ball) from the intermediate plate.



26. REMOVE NO. 1 GEAR SHIFT FORK SHAFT


D029052
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft snap ring from the gear shift fork shaft No. 1.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    D029053
  1. Remove the shift fork set bolt from the gear shift fork No. 1.



    D029054
  1. Remove the gear shift fork shaft No. 1 from the intermediate plate.



    D029055
  1. Remove the gear shift fork No. 1 from the reverse gear.



    D025975
  1. Using a magnetic finger, remove the shift interlock No. 1 roller from the intermediate plate.



27. REMOVE REVERSE SHIFT FORK SHAFT


D029056
  1. Using a pin punch (5 mm) and a hammer, remove the shift fork set slotted spring pin from the gear shift fork No. 3.



    D029057
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft snap ring from the reverse shift fork shaft.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    D029058
  1. Remove the gear shift fork No. 3 and reverse shift fork shaft from the intermediate plate.



    D025975
  1. Using a magnetic finger, remove the shift interlock No. 1 roller from the intermediate plate.



    D025979
  1. Using a magnetic finger, remove the reverse shift fork ball from the reverse shift fork.



28. REMOVE 5TH SHIFT ARM SHAFT


D025980
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft snap ring from the 5th shift arm shaft.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



    C089440
  1. Remove the 5th shift arm shaft from the intermediate plate.

    NOTICE:
    Cover the hole with a shop rag to prevent the reverse shift fork ball from popping out.



    D025982
  1. Using a magnetic finger, remove the reverse shift fork return compression spring from the reverse shift fork.



29. REMOVE REVERSE SHIFT FORK


D025983
  1. Remove the reverse shift fork together with the reverse shift arm from the intermediate plate.



    D025984
  1. Using a screwdriver, remove the reverse shift arm end shaft ring and the reverse shift fork from the reverse shift arm.



30. REMOVE REVERSE SHIFT ARM BRACKET


D025985
  1. Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.



31. REMOVE SPEEDOMETER DRIVE GEAR


G034243
  1. Using snap ring pliers, remove the snap ring.

  1. Remove the speedometer driver gear and ball.

  1. Using a magnetic finger, remove the steel ball.

  1. Using snap ring pliers, remove the snap ring.



32. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING


D029059
  1. Using 2 screwdrivers and a hammer, remove the output shaft bearing shaft snap ring from the output shaft.



33. REMOVE OUTPUT SHAFT REAR BEARING


D025987E02
  1. Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



34. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE


D025991
  1. Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)



35. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE


D025992
  1. Using a dial indicator, measure the radial clearance of the counter shaft 5th gear.

    Standard clearance:
    0.015 to 0.068 mm (0.0059 to 0.0027 in.)

    If the clearance is not within the specified values, replace the counter 5th gear bearing with a new one.



36. REMOVE COUNTER GEAR REAR SHAFT SNAP RING


D025993
  1. Using 2 screwdrivers and a hammer, remove the counter gear rear shaft snap ring from the counter gear.



37. REMOVE NO. 5 GEAR SPLINE PIECE


D025994E01
  1. Using SST, remove the gear spline piece No. 5 from the counter gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021, 09957-04010)



38. REMOVE NO. 3 SYNCHRONIZER RING OUTER


D029060
  1. Remove the synchronizer ring outer No. 3 from the counter gear.



39. REMOVE COUNTER SHAFT 5TH GEAR


D029061
  1. Remove the counter shaft 5th gear and transmission hub sleeve No. 3 assembly from the counter gear.



40. REMOVE COUNTER 5TH GEAR BEARING


C089839
  1. Remove the counter 5th gear bearing from the counter 5th gear.



41. REMOVE NO. 3 TRANSMISSION HUB SLEEVE


D029062
  1. Using a snap ring expander, remove the snap ring.



    D029063
  1. Remove the transmission hub sleeve No. 3, 2 synchromesh shifting keys No. 3 and 2 synchromesh shifting key springs No. 3 from the counter shaft 5th gear.



42. REMOVE 5TH GEAR THRUST WASHER


D025999
  1. Remove the 5th gear thrust washer from the counter gear.



43. REMOVE 5TH GEAR THRUST WASHER PIN


D026000
  1. Remove the 5th gear thrust washer pin from the counter gear.



44. REMOVE OUTPUT SHAFT REAR BEARING RETAINER


D026001
  1. Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.



45. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


D026002
  1. Pull out the reverse idler gear shaft to the rear side and remove the reverse idler gear from the intermediate plate.



46. REMOVE COUNTER SHAFT CENTER BEARING


D029260
  1. Using a snap ring expander, remove the snap ring.



    D026004E01
  1. Using SST, remove the counter shaft center bearing from the intermediate plate.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

    HINT:
    Remove the bearing while tapping the tip of the counter gear so that the counter gear assembly is not pushed forward into the side wall of the output shaft gear.



47. REMOVE COUNTER GEAR


D026005
  1. Remove the counter gear assembly from the intermediate plate.



48. REMOVE INPUT SHAFT ASSEMBLY


D026006
  1. Remove the input shaft assembly and synchronizer ring No. 2 from the output shaft.

    NOTICE:
    Do not drop the input shaft bearing and synchronizer ring No. 2.



49. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING


D029064
  1. Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft.



50. REMOVE OUTPUT SHAFT ASSEMBLY


D029065
  1. Using a plastic hammer, remove the output shaft assembly by tapping the intermediate plate.