Home › TRANSMISSION ยท R155 MANUAL TRANSMISSION › OUTPUT SHAFT

OUTPUT SHAFT > DISASSEMBLY

for Preparation Click here



1. INSPECT 1ST GEAR THRUST CLEARANCE


Z003552E12
  1. Using a dial indicator measure the thrust clearance of the 1st gear.

    Standard clearance:
    0.20 to 0.45 mm(0.0079 to 0.0177 in.)



2. INSPECT 2ND GEAR THRUST CLEARANCE


Z003552E13
  1. Using a dial indicator measure the thrust clearance of the 2nd gear.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)



3. INSPECT 3RD GEAR THRUST CLEARANCE


D026046E03
  1. Using a feeler gauge, measure the thrust clearance of the 3rd gear.

    Standard clearance:
    0.10 to 0.25 mm (0.0039 to 0.0098 in.)



4. INSPECT 1ST GEAR RADIAL CLEARANCE


D026047
  1. Using a dial indicator, measure the radial clearance of the 1st gear.

    Standard clearance:
    0.020 to 0.073 mm (0.0008 to 0.0029 in.)

    If the clearance is not within the specified values, replace the 1st gear needle roller bearing with a new one.



5. INSPECT 2ND GEAR RADIAL CLEARANCE


D026048
  1. Using a dial indicator, measure the radial clearance of the 2nd gear.

    Standard clearance:
    0.015 to 0.068mm (0.0006 to 0.0027 in.)

    If the clearance is not within the specified values, replace the 2nd gear needle roller bearing with a new one.



6. INSPECT 3RD GEAR RADIAL CLEARANCE


D026049
  1. Using a dial indicator, measure the radial clearance of the 3rd gear.

    Standard clearance:
    0.015 to 0.068 mm (0.0006 to 0.0027 in.)

    If the clearance is not within the specified values, replace the 3rd gear needle roller bearing with a new one.



7. REMOVE 1ST GEAR


D026050E02
  1. Using SST and a press, remove the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

    SST
    09950-00020  



8. REMOVE NO. 1 SYNCHRONIZER RING


D026051
  1. Remove synchronizer ring No. 1 (for the 1st gear) from the output shaft.



9. REMOVE 1ST GEAR THRUST WASHER PIN OR BALL


D026052E02
  1. Remove the 1st gear thrust washer pin from the output shaft.



10. REMOVE 1ST GEAR NEEDLE ROLLER BEARING


D026053E02
  1. Remove the 1st gear needle roller bearing from the output shaft.



11. REMOVE 1ST GEAR BEARING SPACER


D026054E03
  1. Remove the 1st gear bearing spacer from the output shaft.



12. REMOVE BEARING SHAFT SNAP RING


D026055
  1. Using 2 screwdrivers and a hammer, remove the bearing shaft snap ring from the output shaft.

    NOTICE:
    Use a shop rag to prevent the snap ring from flying off.



13. REMOVE 2ND GEAR


D026056E02
  1. Using SST and a press, remove the transmission clutch hub No. 1, reverse gear, synchronizer ring No. 1 and 2nd gear from the output shaft.

    SST
    09950-00020  



14. REMOVE 2ND GEAR NEEDLE ROLLER BEARING


D026057E02
  1. Remove the 2nd gear needle roller bearing from the output shaft.



15. REMOVE REVERSE GEAR


D026058
  1. Remove the reverse gear, 3 synchromesh shifting keys No. 1 and 3 synchromesh shifting key springs.
    Use a shop rag to prevent the shifting key and the shifting spring from popping out.



16. REMOVE CLUTCH HUB SET SHAFT SNAP RING


D026059
  1. Using snap ring pliers, remove the clutch hub set shaft snap ring from the output shaft.

    NOTICE:
    Do not damage the sliding surface of the bearing.



17. REMOVE 3RD GEAR


D026060E02
  1. Using SST and a press, remove the clutch hub No. 2 with the hub sleeve No. 2, synchronizer ring No. 2 and 3rd gear from the output shaft.

    SST
    09950-00020  



18. REMOVE 3RD GEAR NEEDLE ROLLER BEARING


D026061E02
  1. Remove the 3rd gear needle roller bearing from the output shaft.



19. REMOVE NO. 2 TRANSMISSION HUB SLEEVE


G038890
  1. Remove the transmission hub sleeve No. 2, 3 synchromesh shifting key springs and 3 synchromesh shifting keys No. 2 from the transmission clutch hub No. 2.