MANUAL TRANSMISSION ASSEMBLY > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Separate Seat Type) |
![]() |
Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.
| 3. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
![]() |
Remove the console box carpet.
![]() |
Remove the 2 screws <F> and 2 bolts <B>.
Disengage the 4 claws and remove the rear console box assembly.
| 4. REMOVE FRONT CONSOLE BOX (for Separate Seat Type) |
![]() |
Remove the shift knob.
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 5. REMOVE FRONT CONSOLE BOX (for Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 6. REMOVE SHIFT LEVER BOOT ASSEMBLY |
![]() |
Remove the 2 screws A, 2 clips B and floor shift lever assembly.
| 7. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY |
![]() |
Cover the shift lever cap with a cloth.
While pressing down on the shift lever cap, turn it counterclockwise to remove.
Pull out the shift lever.
| 8. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY |
Remove the 4 bolts and engine under cover No. 2.
| 9. DRAIN MANUAL TRANSMISSION OIL |
| 10. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
Remove the 2 bolts and 2 compression springs.
Remove the exhaust pipe front from the exhaust pipe support.
Remove the gasket from the exhaust manifold.
| 11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 12. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Access Cab) |
![]() |
Place matchmarks on the propeller shaft flange and differential.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Remove the 2 center support bearing bolts from the frame crossmember.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 13. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab) |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 14. REMOVE STARTER ASSEMBLY |
![]() |
Remove the terminal cap.
Remove the nut, then remove the starter wire harness.
Disconnect the starter connector.
![]() |
Remove the 2 bolts, then remove the starter.
| 15. REMOVE MANIFOLD STAY |
![]() |
Remove the 3 bolts and manifold stay.
| 16. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() |
Remove the 2 bolts and separate the clutch release cylinder assembly.
| 17. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Support the transfer with a support stand.
![]() |
Remove the 4 bolts from the engine rear mounting.
Remove the 4 bolts, nuts and frame crossmember sub- assembly No. 3.
| 18. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR |
![]() |
Remove the 4 bolts and engine mounting insulator rear No. 1.
Using a transmission jack, support the transmission unit assembly.
Remove the support stand from the rear side of the transfer.
| 19. DISCONNECT WIRE HARNESS |
Tilt the transmission assembly downward.
Disconnect the back-up lamp switch connector.
Disconnect the speed sensor connector.
Disconnect the 2 transfer indicator switch connectors.
Disconnect the transfer shift actuator motor connector.
Disconnect the wire harness clamp from the transmission w/ transfer assembly.
| 20. REMOVE MANUAL TRANSMISSION WITH TRANSFER |
![]() |
Remove the 7 bolts and remove the transmission assembly.
| 21. REMOVE TRANSFER ASSEMBLY |
![]() |
Remove the 8 transfer adaptor rear mounting bolts.
Pull the transfer straight up and remove it from the transmission.