Home › TRANSMISSION ยท R155F MANUAL TRANSMISSION › TRANSFER ADAPTOR OIL SEAL

TRANSFER ADAPTOR OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ADAPTER OIL SEAL


G021436E01
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09223-00010  

    Drive in depth:
    45.4 to 46.4 mm (1.787 to 1.827 in.)

    NOTICE:
    Be careful not to damage the oil seal.

  1. Coat the lip of the oil seal with MP grease.



2. INSTALL TRANSFER ASSEMBLY


F050671
  1. Install the transfer assembly with the 8 bolts.

    Torque:
    24 N*m{ 244 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.



3. INSTALL MANUAL TRANSMISSION WITH TRANSFER


F050669E02
  1. Align the input shaft with the clutch disc and install the transmission unit assembly onto the engine.

  1. Install the 7 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf } for bolt A37 N*m{ 379 kgf*cm , 27 ft.*lbf } for bolt B and C

    HINT:
    Install bolt B from the front of the vehicle direction.



4. CONNECT WIRE HARNESS
  1. Connect the wire harness clamp to the transmission w/ transfer assembly.

  1. Connect the back-up lamp switch connector.

  1. Connect the speed sensor connector.

  1. Connect the 2 transfer indicator switch connectors.

  1. Connect the transfer shift actuator motor connector.



5. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G021430
  1. Install the engine mount insulator rear No. 1 with 4 bolts onto the transmission assembly.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



6. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G021429
  1. Install the frame crossmember sub-assembly No. 3 with the 8 bolts and nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the 4 bolts onto the engine mounting insulator rear No. 1.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



7. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY


G021426
  1. Install the clutch release cylinder assembly with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. INSTALL STARTER ASSEMBLY


G037950E01
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    G037949E01
  1. Connect the starter connector.

  1. Install the starter wire harness with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.



9. INSTALL MANIFOLD STAY


F050668E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf } for bolt A
    44 N*m{ 449 kgf*cm , 33 ft.*lbf } for bolt B
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt C



10. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Access Cab)


11. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab)


12. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


13. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A077857E01
  1. Check the free length.

    1. Using vernier calipers, measure the free length of the compression spring.

      Minimum:
      40.5 mm (1.594 in.)

      If the free length is less than the minimum, replace the compression spring.



    A076194E06
  1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the exhaust manifold.

    NOTICE:
    1. Make sure that the gasket is in the correct angle when installing.
    2. Do not reuse the removed gasket.
    3. Never push a new gasket into the exhaust manifold by installing the exhaust pipe front into the exhaust manifold.

  1. Install the exhaust pipe front into the exhaust pipe support.

  1. Tighten the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



14. ADD MANUAL TRANSMISSION OIL


15. ADJUST MANUAL TRANSMISSION OIL


D025304E01
  1. Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest point of the transmission filler plug opening.

    NOTICE:
    1. Problems may occur when the oil level is too high or low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage when the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



16. INSTALL NO.2 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the engine under cover No. 2 with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



17. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY


F050670E01
  1. Cover the shift lever cap with a cloth.

  1. While pressing down on the shift lever, turn it clockwise to install.

    HINT:
    Apply MP grease to the tip of the shift lever.



18. INSTALL SHIFT LEVER BOOT ASSEMBLY


F050667E01
  1. Install the shift lever boot assembly with the 2 screws A and 2 clips B.



19. INSTALL FRONT CONSOLE BOX (for Bench Seat Type)


B085776E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B085775E01
  1. Install the No. 2 box bottom mat.

  1. Install the instrument panel cup holder.

  1. Install the box bottom mat.

  1. Install the shift knob.



20. INSTALL FRONT CONSOLE BOX (for Separate Seat Type)


    B085814E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



21. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



22. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Separate Seat Type)


    B085770E01
  1. Engage the 4 clips and claw, and remove the console upper panel sub-assembly.



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



24. CHECK FOR MANUAL TRANSMISSION OIL LEAKAGE