Home › TRANSMISSION ยท RA60 MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY


F051846E01
  1. Install the manual transmission case cover with the 5 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8.5 ft.*lbf }



2. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY


F051064E03
  1. Install the manual transmission with the 9 bolts.

    Torque:
    72 N*m{ 730 kgf*cm , 53 ft.*lbf } for bolt A
    37 N*m{ 380 kgf*cm , 28 ft.*lbf } for bolt B



3. CONNECT WIRE HARNESS


4. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


F051063E01
  1. Install the engine mounting insulator rear No. 1 with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



5. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


F042938E01
  1. Install the frame crossmember sub-assembly No. 3 with the 4 bolts and 4 nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the frame crossmember sub-assembly No. 3 with the 4 bolts.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



6. INSTALL CLUTCH ACCUMULATOR ASSEMBLY


F050797E01
  1. Using SST, connect the 2 flexible hose tubes to the clutch accumulator.

    SST
    09023-00101  



    F050798
  1. Install the clutch accumulator with the 3 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf }



    F050797E01
  1. Using SST, tighten the 2 flexible hose tubes.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



7. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY


F050800
  1. Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf }



8. INSTALL NO. 1 CLUTCH HOUSING COVER


F050796
  1. Install the clutch housing cover No. 1 with the 3 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf }



9. INSTALL STARTER ASSEMBLY
  1. Install the starter assembly with the 2 bolts.

    Torque:
    :
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the wire harness with the nut to terminal 30.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Connect terminal 50 to the starter assy.



10. INSTALL MANIFOLD STAY


F051649E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



11. INSTALL NO. 2 MANIFOLD STAY


F051648E01
  1. Install the manifold stay No. 2 with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



12. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with the 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.



    F052184E02
  1. Adjust the center support bearing.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing to keep the intervals, as shown.
    2. In the same condition, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.039 to 0.039 in.) of each other in the vehicle's longitudinal direction when the vehicle is unladen.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



13. INSTALL EXHAUST PIPE
  1. Install a new gasket onto the exhaust manifold RH.

  1. Install the exhaust front pipe with the new 2 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



14. ADD MANUAL TRANSMISSION OIL


15. ADJUST MANUAL TRANSMISSION OIL


D025304E03
  1. Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest point of the transmission filler plug opening.

    NOTICE:
    1. Problems may occur when the oil level is too high or low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage when the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



16. INSTALL NO.2 ENGINE UNDER COVER


17. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY


F051066E01
  1. Apply MP grease to the tip of the shift lever.



    F051824E01
  1. Cover the shift lever cap with a cloth.

  1. Pressing down on the shift lever cap, turn it clockwise to install the shift lever.



18. INSTALL SHIFT LEVER BOOT ASSEMBLY
  1. Install the shift lever boot with the 2 screws and 2 clips.



19. INSTALL FRONT CONSOLE BOX


    B085814E01
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



20. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


21. INSTALL REAR CONSOLE BOX ASSEMBLY


    B085820E01
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.



    B085771E01
  1. Install the console box carpet.



22. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B085770E01
  1. Engage the 4 clips and claw, and remove the console upper panel sub-assembly.



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }