Home › TRANSMISSION ยท RA60F MANUAL TRANSMISSION › INPUT SHAFT

INPUT SHAFT > DISASSEMBLY

for Preparation Click here



1. INSPECT 6TH GEAR THRUST CLEARANCE


F051109E01
  1. Using a dial indicator, measure the 6th gear thrust clearance.

    Standard clearance:
    0.20 to 0.49 mm (0.0079 to 0.0193 in.)

    If the clearance is outside the specification, replace the synchronizer ring No. 3.



2. INSPECT 3RD GEAR THRUST CLEARANCE


F051110E01
  1. Using a feeler gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.09 to 0.52 mm (0.0035 to 0.0205 in.)

    If the clearance is outside the specification, replace the synchronizer ring set No. 2.



3. INSPECT 4TH GEAR THRUST CLEARANCE


F051111E01
  1. Using a dial indicator, measure the 4th gear thrust clearance.

    Standard clearance:
    0.12 to 0.38 mm (0.0047 to 0.0150 in.)

    If the clearance is outside the specification, replace the synchronizer ring No. 3.



4. INSPECT 6TH GEAR RADIAL CLEARANCE


F051106E01
  1. Using a dial indicator, measure the 6th gear radial clearance.

    Standard clearance:
    0.015 to 0.065 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.



5. INSPECT 3RD GEAR RADIAL CLEARANCE


F051107E01
  1. Using a dial indicator, measure the 3rd gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.



6. INSPECT 4TH GEAR RADIAL CLEARANCE


F051108E01
  1. Using a dial indicator, measure the 4th gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.



7. REMOVE TRANSMISSION CLUTCH HUB NO.3 SHAFT SNAP RING


D033652E01
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag to prevent the snap ring from flying off.



8. REMOVE 6TH GEAR


D033653E01
  1. Using SST and a press, remove the transmission clutch hub No. 3, hub sleeve, synchronizer ring and 6th gear from the input shaft.

    SST
    09950-00020  
    09950-70010   (09951-07200)
    09950-60010   (09951-00300)

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand so that it does not fall off.



9. REMOVE 6TH GEAR NEEDLE ROLLER BEARING


F051087E01
  1. Remove the 6th gear needle roller bearing from the input shaft.



10. REMOVE SHAFT SNAP RING


F051088E01
  1. Remove the shaft snap ring from the input shaft.



11. REMOVE GEAR THRUST WASHER SHAFT SNAP RING


D033654E01
  1. Using a snap ring expander, remove the snap ring from the input shaft.



12. REMOVE 3RD GEAR THRUST WASHER


F051090E01
  1. Remove the 3rd gear thrust washer from the input shaft.



13. REMOVE 3RD GEAR


F051091E01
  1. Remove the 3rd gear from the input shaft.



14. REMOVE STRAIGHT PIN


F051092E01
  1. Remove the straight pin from the input shaft.



15. REMOVE 3RD GEAR NEEDLE ROLLER BEARING


F051093E01
  1. Remove the 3rd gear needle roller bearing from the input shaft.



16. REMOVE SPACER


F051094E01
  1. Remove the spacer from the input shaft.



17. REMOVE NO. 2 SYNCHRONIZER RING SET


F051095E01
  1. Remove the synchronizer ring set No. 2 from the input shaft.



18. REMOVE CLUTCH HUB NO.2 SETTING SHAFT SNAP RING


D033657E01
  1. Using a snap ring expander, remove the snap ring from the input shaft.



19. REMOVE 4TH GEAR


D033658E01
  1. Using SST and a press, remove the transmission clutch hub No. 2, hub sleeve, synchronizer ring and 4th gear from the input shaft.

    SST
    09950-00020  

    NOTICE:
    Support the input shaft by hand so that it does not fall off.



20. REMOVE 4TH GEAR NEEDLE ROLLER BEARING


F051098E01
  1. Remove the 4th gear needle roller bearing from the input shaft.



21. REMOVE INPUT SHAFT FRONT BEARING SNAP RING


D033659E01
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag to prevent the snap ring from flying off.



22. REMOVE INPUT SHAFT FRONT BEARING


D033660E01
  1. Using SST and a press, remove the input shaft front bearing from the input shaft.

    SST
    09950-00020  

    NOTICE:
    Support the input shaft by hand so that it does not fall off.



23. REMOVE NO. 2 TRANSMISSION CLUTCH HUB


F051610E01
  1. Remove the clutch hub, 3 synchromesh shifting keys, 3 balls and 3 springs from the hub sleeve.

    HINT:
    Use a shop rag to prevent the ball and spring from flying off.



24. REMOVE NO. 3 TRANSMISSION CLUTCH HUB
  1. Perform the same procedures as for clutch hub No. 2.