Home › TRANSMISSION ยท RA60 MANUAL TRANSMISSION › COUNTER GEAR AND REVERSE IDLER GEAR

COUNTER GEAR AND REVERSE IDLER GEAR > DISASSEMBLY

for Preparation Click here



1. INSPECT REVERSE GEAR THRUST CLEARANCE


F051532E01
  1. Using a feeler gauge, measure the reverse gear thrust clearance.

    Standard clearance:
    0.12 to 0.37 mm (0.0047 to 0.0146 in.)

    If the clearance is outside the specification, replace the synchronizer ring No. 4.



2. INSPECT 1ST GEAR THRUST CLEARANCE


F051533E01
  1. Using a dial indicator, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.43 mm (0.0039 to 0.0169 in.)

    If the clearance is outside the specification, replace the synchronizer ring set No. 1.



3. INSPECT 2ND GEAR THRUST CLEARANCE


F051534E01
  1. Using a dial indicator, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.43 mm (0.0039 to 0.0169 in.)

    If the clearance is outside the specification, replace the synchronizer ring set No. 1.



4. INSPECT REVERSE GEAR RADIAL CLEARANCE


F051535E01
  1. Using a dial indicator, measure the reverse gear radial clearance.

    Standard clearance:
    0.015 to 0.065 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the reverse gear needle roller bearing or shaft.



5. INSPECT 1ST GEAR RADIAL CLEARANCE


F051536E01
  1. Using a dial indicator, measure the 1st gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the 1st gear needle roller bearing or shaft.



6. INSPECT 2ND GEAR RADIAL CLEARANCE


F051537E01
  1. Using a dial indicator, measure the 2nd gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the 2nd gear needle roller bearing or shaft.



7. REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING


D033690E01
  1. Using a snap ring expander, remove the snap ring from the counter gear.



8. REMOVE COUNTER GEAR FRONT BEARING OR ROLLER


F051539E01
  1. Using SST and a press, remove the counter gear front bearing or roller from the counter gear.

    SST
    09950-00020  
    09950-70010   (09951-07100)
    09950-60010   (09951-00320)



9. REMOVE REVERSE GEAR BEARING RACE INNER


F051540E01
  1. Remove the reverse gear bearing race inner from the counter gear.



10. REMOVE COUNTERSHAFT REVERSE GEAR


F051541E01
  1. Remove the countershaft reverse gear from the counter gear.

  1. Remove the hub sleeve, 2 shifting keys and key spring from the countershaft reverse gear.



11. REMOVE REVERSE GEAR NEEDLE ROLLER BEARING


F051542E01
  1. Remove the reverse gear needle roller bearing from the counter gear.



12. REMOVE NO. 4 SYNCHRONIZER RING


F051543E01
  1. Remove the synchronizer ring No. 4 from the counter gear.



13. REMOVE BALL


F051544E01
  1. Remove the ball from the counter gear.



14. REMOVE COUNTERSHAFT GEAR 1ST SPEED


F051630E01
  1. Using a press, remove the countershaft gear 1st speed together with reverse gear spline piece from the counter gear.

    SST
    09950-00020  



15. REMOVE 1ST GEAR NEEDLE ROLLER BEARING


F051546E01
  1. Remove the 1st gear needle roller bearing from the counter gear.



16. REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)


F051631E01
  1. Remove the synchronizer ring set No. 1 from the counter gear.



17. REMOVE CLUTCH HUB NO.1 SHAFT SNAP RING


D033696E01
  1. Using a snap ring expander, remove the snap ring from the counter gear.



18. REMOVE COUNTER SHAFT 2ND SPEED GEAR


F051632E01
  1. Using a press, remove the counter shaft 2nd speed gear together with transmission clutch hub No. 1 from the counter gear.

    SST
    09950-00020  



19. REMOVE 2ND GEAR NEEDLE ROLLER BEARING


F051551E01
  1. Remove the 2nd needle roller bearing from the counter gear.



20. REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 2ND GEAR)


F051633E01
  1. Remove the synchronizer ring set No. 1 from the 2nd gear.



21. REMOVE NO. 1 TRANSMISSION CLUTCH HUB


F051634E01
  1. Remove the hub sleeve, 3 synchromesh shifting keys, 3 balls and 3 springs from the clutch hub.

    HINT:
    Use a shop rag to prevent the ball and spring from flying off.



22. REMOVE SNAP RING COUNTER GEAR REAR BEARING


D033689E01
  1. Using a snap ring expander, remove the snap ring from the counter gear.



23. REMOVE RADIAL BALL BEARING INNER RACE


F051635E01
  1. Using SST and a press, remove the needle roller bearing inner race.

    SST
    09950-00020