COUNTER GEAR AND REVERSE IDLER GEAR > DISASSEMBLY |
| 1. INSPECT REVERSE GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the reverse gear thrust clearance.
| 2. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 1st gear thrust clearance.
| 3. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 2nd gear thrust clearance.
| 4. INSPECT REVERSE GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the reverse gear radial clearance.
| 5. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 1st gear radial clearance.
| 6. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 2nd gear radial clearance.
| 7. REMOVE COUNTER GEAR FRONT BEARING SNAP RING NO.1 |
![]() |
Using a snap ring expander, remove the snap ring from the counter gear.
| 8. REMOVE COUNTER GEAR FRONT BEARING OR ROLLER |
![]() |
Using SST and a press, remove the counter gear front bearing or roller from the counter gear.
| 9. REMOVE REVERSE GEAR BEARING RACE INNER |
![]() |
Remove the reverse gear bearing race inner from the counter gear.
| 10. REMOVE COUNTERSHAFT REVERSE GEAR |
![]() |
Remove the countershaft reverse gear from the counter gear.
Remove the hub sleeve, 2 shifting keys and key spring from the countershaft reverse gear.
| 11. REMOVE REVERSE GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the reverse gear needle roller bearing from the counter gear.
| 12. REMOVE NO. 4 SYNCHRONIZER RING |
![]() |
Remove the synchronizer ring No. 4 from the counter gear.
| 13. REMOVE BALL |
![]() |
Remove the ball from the counter gear.
| 14. REMOVE COUNTERSHAFT GEAR 1ST SPEED |
![]() |
Using a press, remove the countershaft gear 1st speed together with reverse gear spline piece from the counter gear.
| 15. REMOVE 1ST GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 1st gear needle roller bearing from the counter gear.
| 16. REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR) |
![]() |
Remove the synchronizer ring set No. 1 from the counter gear.
| 17. REMOVE CLUTCH HUB NO.1 SHAFT SNAP RING |
![]() |
Using a snap ring expander, remove the snap ring from the counter gear.
| 18. REMOVE COUNTER SHAFT 2ND SPEED GEAR |
![]() |
Using a press, remove the counter shaft 2nd speed gear together with transmission clutch hub No. 1 from the counter gear.
| 19. REMOVE 2ND GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 2nd needle roller bearing from the counter gear.
| 20. REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 2ND GEAR) |
![]() |
Remove the synchronizer ring set No. 1 from the 2nd gear.
| 21. REMOVE NO. 1 TRANSMISSION CLUTCH HUB |
![]() |
Remove the hub sleeve, 3 synchromesh shifting keys, 3 balls and 3 springs from the clutch hub.
| 22. REMOVE SNAP RING COUNTER GEAR REAR BEARING |
![]() |
Using a snap ring expander, remove the snap ring from the counter gear.
| 23. REMOVE RADIAL BALL BEARING INNER RACE |
![]() |
Using SST and a press, remove the needle roller bearing inner race.