Home › TRANSMISSION ยท RA60F MANUAL TRANSMISSION › COUNTER GEAR AND REVERSE IDLER GEAR

COUNTER GEAR AND REVERSE IDLER GEAR > REASSEMBLY

for Preparation Click here



1. INSTALL RADIAL BALL BEARING INNER RACE


F051640E01
  1. Using SST and a press, install a new needle roller bearing inner race.

    SST
    09950-60010   (09951-00540)



2. INSTALL SNAP RING COUNTER GEAR REAR BEARING


D033689E01
  1. Select a snap ring that will allow minimum axial play.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Snap ring thickness:
    Part No.
    Thickness: mm (in.)
    Mark
    90520-31015
    2.35 to 2.40
    (0.0925 to 0.0945)
    A
    90520-31016
    2.40 to 2.45
    (0.0945 to 0.0965)
    B
    90520-31017
    2.45 to 2.50
    (0.0965 to 0.0984)
    C
    90520-31018
    2.50 to 2.55
    (0.0984 to 0.1004)
    D
    90520-31019
    2.55 to 2.60
    (0.1004 to 0.1024)
    E
    90520-31020
    2.60 to 2.65
    (0.1024 to 0.1043)
    F
    90520-31021
    2.65 to 2.70
    (0.1043 to 0.1063)
    G
    90520-31022
    2.70 to 2.75
    (0.1063 to 0.1083)
    H
    90520-31023
    2.75 to 2.80
    (0.1083 to 0.1102)
    J
    90520-31024
    2.80 to 2.85
    (0.1102 to 0.1122)
    K
    90520-31025
    2.85 to 2.90
    (0.1122 to 0.1142)
    L
    90520-31033
    2.90 to 2.95
    (0.1142 to 0.1161)
    M

  1. Using a snap ring expander, install the snap ring onto the counter gear.



3. INSTALL NO. 1 TRANSMISSION CLUTCH HUB


F051641E01
  1. Apply a light coat of gear oil to the sleeve and hub.

  1. Install the clutch hub sleeve onto the clutch hub.

  1. Install the 3 shifting keys onto the clutch hub.

  1. Install the 3 shifting key springs onto the clutch hub.

  1. Place the ball in the hole of the shifting key, and install the hub sleeve while pushing in the ball.

    NOTICE:
    Take care to prevent the ball from flying off.



4. INSTALL 2ND GEAR NEEDLE ROLLER BEARING


F051551E01
  1. Coat the 2nd gear needle roller bearing with gear oil, then install it onto the counter gear.



5. INSTALL COUNTER SHAFT 2ND SPEED GEAR


F051642E01
  1. Coat the countershaft 2nd speed gear with gear oil, then install it onto the counter gear.

  1. Coat the synchronizer ring set No. 1 with gear oil, then install it onto the counter gear.

  1. Using SST and a press, install the transmission clutch hub No. 1 onto the counter gear.

    SST
    09308-14010  

    HINT:
    Align the convex portion of the synchronizer ring with the groove of the clutch hub.

  1. Install the clutch hub and confirm that the gear and synchronizer ring move smoothly.



6. INSTALL CLUTCH HUB NO.1 SHAFT SNAP RING


D033696E01
  1. Select a snap ring that will allow minimum axial play.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Snap ring thickness:
    Part No.
    Thickness: mm (in.)
    Mark
    90520-45013
    2.28 to 2.33
    (0.0898 to 0.0917)
    A
    90520-45014
    2.33 to 2.38
    (0.0917 to 0.0937)
    B
    90520-45015
    2.38 to 2.43
    (0.0937 to 0.0957)
    C
    90520-45016
    2.43 to 2.48
    (0.0957 to 0.0976)
    D
    90520-45017
    2.48 to 2.53
    (0.0976 to 0.0996)
    E
    90520-45018
    2.53 to 2.58
    (0.0996 to 0.1016)
    F
    90520-45019
    2.58 to 2.63
    (0.1016 to 0.1035)
    G

  1. Using a snap ring expander, install the snap ring onto the counter gear.



7. INSTALL NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)


F051547E01
  1. Coat the synchronizer ring set No. 1 with gear oil, then install it onto the counter gear.



8. INSTALL 1ST GEAR NEEDLE ROLLER BEARING


F051546E01
  1. Coat the 1st gear needle roller bearing with gear oil, then install it onto the counter gear.



9. INSTALL COUNTERSHAFT GEAR 1ST SPEED


F051561E01
  1. Coat the countershaft gear 1st speed with gear oil, and install it onto the counter gear.

  1. Using SST and a press, install the reverse gear spline piece.

    SST
    09309-37010  



10. INSTALL BALL


F051544E01
  1. Install the ball into the counter gear.



11. INSTALL NO. 4 SYNCHRONIZER RING


F051543E01
  1. Coat the synchronizer ring No. 4 with gear oil, and install it onto the counter gear.



12. INSTALL REVERSE GEAR NEEDLE ROLLER BEARING


F051542E01
  1. Coat the reverse gear needle roller bearing with gear oil, and install it onto the counter gear.



13. INSTALL COUNTERSHAFT REVERSE GEAR


F051643E01
  1. Install the key spring and 2 shifting keys onto the reverse gear.

    HINT:
    1. Install the shifting key with its groove on the reverse gear side.
    2. Install the key spring with its claw on the reverse gear side.
    3. Refer to the illustration when installing the key spring.

  1. Install the hub sleeve onto the reverse gear.

  1. Coat the countershaft reverse gear with gear oil, then install it onto the counter gear.



14. INSTALL REVERSE GEAR BEARING RACE INNER


F051564E01
  1. Align the groove of the reverse gear bearing race inner with the ball, and install them.



15. INSTALL COUNTER GEAR FRONT BEARING OR ROLLER


F051644E01
  1. Using SST and a press, install counter gear front bearing or roller onto the counter gear.

    SST
    09608-06041  

    HINT:
    Make sure that the groove of the bearing faces the correct direction as shown in the illustration.



16. REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING


F051566E01
  1. Select a snap ring that will allow minimum axial play.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Snap ring thickness:
    Part No.
    Thickness: mm (in.)
    Mark
    90520-31015
    2.35 to 2.40
    (0.0925 to 0.0945)
    A
    90520-31016
    2.40 to 2.45
    (0.0945 to 0.0965)
    B
    90520-31017
    2.45 to 2.50
    (0.0965 to 0.0984)
    C
    90520-31018
    2.50 to 2.55
    (0.0984 to 0.1004)
    D
    90520-31019
    2.55 to 2.60
    (0.1004 to 0.1024)
    E
    90520-31020
    2.60 to 2.65
    (0.1024 to 0.1043)
    F
    90520-31021
    2.65 to 2.70
    (0.1043 to 0.1063)
    G
    90520-31022
    2.70 to 2.75
    (0.1063 to 0.1083)
    H
    90520-31023
    2.75 to 2.80
    (0.1083 to 0.1102)
    J
    90520-31024
    2.80 to 2.85
    (0.1102 to 0.1122)
    K
    90520-31025
    2.85 to 2.90
    (0.1122 to 0.1142)
    L
    0520-31033
    2.90 to 2.95
    (0.1142 to 0.1161)
    M

  1. Using a snap ring expander, install the snap ring onto the counter gear.



17. INSPECT REVERSE GEAR THRUST CLEARANCE


F051532E01
  1. Using a feeler gauge, measure the reverse gear thrust clearance.

    Standard clearance:
    0.12 to 0.37 mm (0.0047 to 0.0146 in.)

    If the clearance is outside the specification, replace the synchronizer ring No. 4.



18. INSPECT 1ST GEAR THRUST CLEARANCE


F051533E01
  1. Using a dial indicator, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.43 mm (0.0039 to 0.0169 in.)

    If the clearance is outside the specification, replace the synchronizer ring set No. 1.



19. INSPECT 2ND GEAR THRUST CLEARANCE


F051534E01
  1. Using a dial indicator, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.43 mm (0.0039 to 0.0169 in.)

    If the clearance is outside the specification, replace the synchronizer ring set No. 1.



20. INSPECT REVERSE GEAR RADIAL CLEARANCE


F051535E01
  1. Using a dial indicator, measure the reverse gear radial clearance.

    Standard clearance:
    0.015 to 0.065 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the reverse gear needle roller bearing or shaft.



21. INSPECT 1ST GEAR RADIAL CLEARANCE


F051536E01
  1. Using a dial indicator, measure the 1st gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the 1st gear needle roller bearing or shaft.



22. INSPECT 2ND GEAR RADIAL CLEARANCE


F051537E01
  1. Using a dial indicator, measure the 2nd gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.0006 to 0.0026 in.)

    If the clearance is outside the specification, replace the 2nd gear needle roller bearing or shaft.