Home › TRANSMISSION ยท RA60F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



3. REMOVE REAR CONSOLE BOX ASSEMBLY


    B085771E01
  1. Remove the console box carpet.



    B085772E01
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


5. REMOVE FRONT CONSOLE BOX


    B085813E01
  1. Remove the shift knob.

  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



6. REMOVE SHIFT LEVER BOOT ASSEMBLY


F051061
  1. Remove the 2 screws and 2 clips, then remove the shift lever boot.



7. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY


F051062
  1. Separate the shift lever cap boot from the manual transmission.



    F051209E01
  1. Cover the shift lever cap with a cloth.

  1. Pressing down on the shift lever cap, turn it counterclockwise to remove the shift lever.

  1. Pull out the shift lever.



8. REMOVE NO. 2 ENGINE UNDER COVER


9. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the drain plug, gasket and then drain the manual transmission oil.

  1. Install a new gasket and drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



10. REMOVE EXHAUST PIPE ASSEMBLY
  1. Remove the 2 nuts, then remove the exhaust front pipe.



11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


C098708E02
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



12. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



13. REMOVE NO. 2 MANIFOLD STAY


F051648
  1. Remove the 3 bolts and manifold stay No. 2.



14. REMOVE MANIFOLD STAY


F051649
  1. Remove the 3 bolts and manifold stay.



15. REMOVE STARTER ASSEMBLY


    G036168E01
  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut, then remove the wire harness from terminal 30.

  1. Remove the 2 bolts, then remove the starter assembly.



16. REMOVE NO. 1 CLUTCH HOUSING COVER


F050796
  1. Remove the 3 bolts and clutch housing cover No. 1.



17. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY


F050800
  1. Remove the 2 bolts and pull out the clutch release cylinder.



18. REMOVE CLUTCH ACCUMULATOR ASSEMBLY


F050797E01
  1. Using SST, disconnect the 2 flexible hose tubes from the clutch accumulator.

    SST
    09023-00101  

    HINT:
    Use a container to catch the fluid.



    F050798
  1. Remove the 3 bolts and clutch accumulator.



19. SUPPORT MANUAL TRANSMISSION WITH TRANSFER
  1. Support the manual transmission with a transmission jack.



20. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


F042938
  1. Remove the 4 bolts on the frame crossmember sub-assembly No. 3.

  1. Remove the 4 nuts, 4 bolts and frame crossmember sub-assembly No. 3.



21. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR


F051063
  1. Remove the 4 bolts and engine mounting insulator rear from the manual transmission.



22. DISCONNECT CONNECTOR
  1. Tilt down the transmission.

  1. Disconnect the transfer shift actuator connector.

  1. Disconnect the transfer indicator switch No. 1 connector.

  1. Disconnect the transfer indicator switch No. 2 connector.

  1. Disconnect the speedometer sensor connector.

  1. Disconnect the back up lamp switch connector.



23. DISCONNECT WIRE HARNESS


24. REMOVE MANUAL TRANSMISSION WITH TRANSFER


F051064
  1. Remove the 9 bolts.

  1. Separate and remove the manual transmission.



25. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY


F051065
  1. Remove the 5 bolts and manual transmission case cover.



26. REMOVE TRANSFER ASSEMBLY


F050671
  1. Remove the 8 transfer adaptor rear mounting bolts.

  1. Pull the transfer straight up and remove it from the transmission.

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.