MANUAL TRANSMISSION UNIT > REASSEMBLY |
| 1. INSTALL 1ST AND REVERSE SHIFT ARM |
![]() |
Install the shift arm and shift arm pivot onto the interlock bracket.
![]() |
Install a new E-ring onto the shift arm pivot.
| 2. INSTALL NO. 4 GEAR SHIFT SHAFT |
![]() |
Install the spring and ball onto the interlock bracket.
Install the shift fork shaft No. 4.
| 3. INSTALL NO. 4 GEAR SHIFT FORK |
![]() |
Install the shift fork No. 4 onto the shift fork shaft No. 4.
Using a pin punch (5 mm (0.20 in.)) and hammer, tap the new slotted pin into the shaft fork No. 4 and shift fork shaft No. 4.
| 4. INSTALL NO. 1 GEAR SHIFT FORK |
![]() |
Install the shift fork No. 1 and shift head No. 2 onto the shift fork shaft No. 4.
Using a pin punch (5 mm (0.20 in.)) and hammer, tap the new slotted pin into the shaft head No. 2 and shift fork shaft No. 4.
| 5. INSTALL NO. 1 GEAR SHIFT FORK SHAFT |
![]() |
Apply MP grease to the interlock pin No. 1 and install it onto the interlock bracket.
Install the spring and ball onto the interlock bracket.
Install the shift fork shaft No. 1 onto the interlock bracket.
| 6. INSTALL NO. 1 GEAR SHIFT HEAD |
![]() |
Install the shift head No. 1 into the shift fork shaft No. 1.
Using a pin punch (5 mm (0.20 in.)) and hammer, tap the new slotted pin into the shaft head No. 1 and shift fork shaft No. 1.
| 7. INSTALL NO. 2 GEAR SHIFT FORK SHAFT |
![]() |
Apply MP grease to the interlock pins No. 2 and No. 3, then install them onto the interlock bracket.
Install the spring and ball the interlock bracket.
Install the shift fork shaft No. 2 onto the interlock bracket.
| 8. INSTALL NO. 2 GEAR SHIFT FORK |
![]() |
Install the shift fork No. 2 with the bolt.
| 9. INSTALL NO. 3 GEAR SHIFT FORK SHAFT |
![]() |
Apply MP grease to the interlock pins No. 2 and No. 3, then install them onto the interlock bracket.
Install the spring and ball onto the interlock bracket.
Install the shift fork shaft No. 3 onto the interlock bracket.
| 10. INSTALL NO. 3 GEAR SHIFT FORK |
![]() |
Install the shift fork No. 3 with the bolt.
| 11. INSTALL TRANSMISSION CASE OIL SEAL |
![]() |
Using SST and a hammer, tap a new oil seal into the front case in accordance with the dimension specified in the illustration.
Apply gear oil to the lip of the oil seal.
| 12. INSTALL FRONT BEARING SHAFT SNAP RING |
![]() |
Using a snap ring plier, install the 2 snap rings.
| 13. INSTALL NO. 1 OIL RECEIVER PIPE |
![]() |
Install the oil receiver pipe No. 1 onto the transmission front case.
| 14. INSTALL TRANSMISSION FRONT CASE |
![]() |
Apply gear oil to all sliding and rotating parts.
Provisionally install the output shaft, input shaft, counter gear shaft and control assembly, and tie them with a rope or string.
![]() |
Using a snap ring expander, extend the 2 snap rings and install the output shaft, input shaft, counter gear shaft and control assembly.
Untie the output shaft, input shaft, counter gear shaft and control assembly.
![]() |
Using a hexagonal wrench (24 mm), install the plug onto the front case.
![]() |
Install the 4 bolts onto the interlock bracket.
| 15. INSTALL REVERSE IDLER GEAR |
![]() |
Install the reverse idler gear, reverse idler gear bearing and reverse idler gear shaft.
| 16. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY |
![]() |
Using SST, install the back-up light switch with a new gasket onto the transmission front case.
| 17. INSTALL SHIFT AND SELECT LEVER CAM |
![]() |
Install the shift and select lever cam onto the shaft and install a new E-ring.
| 18. INSTALL SHIFT AND SELECT LEVER |
![]() |
Install the lock ball pin and spring onto the shift and select lever.
Install the shift and select lever onto the shift and select lever cam and shaft.
Install the bolt onto the shift and select lever.
| 19. INSTALL SHIFT AND SELECT LEVER SHAFT |
![]() |
Align the groove of the shift and select cam with the reverse idler shaft, and the claw with the groove of the control assembly, and install them.
| 20. INSTALL NO. 2 OIL RECEIVER PIPE |
![]() |
Install the oil receiver pipe No. 2 into the transmission middle case.
| 21. INSTALL DRAIN PLUG SUB-ASSEMBLY |
![]() |
Install the drain plug with a new gasket onto the transmission middle case.
| 22. INSTALL TRANSMISSION MIDDLE CASE |
![]() |
Apply FIPG to the transmission middle case, as shown in the illustration.
![]() |
Install the transmission middle case with the 11 bolts onto the transmission front case.
| 23. INSTALL REVERSE IDLER GEAR SHAFT BOLT |
![]() |
Install a new gasket and the reverse idler gear shaft bolt onto the reverse idler gear shaft.
| 24. INSTALL TRANSMISSION OIL SEPARATOR |
![]() |
Install the transmission oil separator with the 2 bolts.
| 25. INSTALL COUNTER GEAR REAR RADIAL BALL BEARING |
![]() |
Coat a new counter gear rear radial ball bearing with gear oil, and using SST and a press, install it into the transmission rear case.
![]() |
Install the bearing lock plate with the bolt.
| 26. INSTALL OUTPUT SHAFT REAR BEARING OUTER RACE |
![]() |
Using SST and a press, press in 2 new bearing outer races.
| 27. INSTALL OIL SEPARATOR PACKING SEAL |
![]() |
Install the oil separator packing seal onto the transmission rear case.
| 28. INSTALL EXTENSION HOUSING OIL RECEIVER PIPE |
![]() |
Install the extension housing oil receiver pipe onto the transmission rear case.
| 29. INSTALL MANUAL TRANSMISSION FILLER PLUG |
![]() |
Install the 2 transmission filler plugs with 2 new gaskets onto the transmission rear case.
| 30. INSTALL TRANSMISSION REAR CASE |
![]() |
Apply FIPG to the transmission rear case, as shown in the illustration.
![]() |
Install the transmission rear case with the 10 bolts and 3 brackets onto the transmission middle case.
| 31. INSTALL SHIFT DETENT BALL PLUG |
![]() |
Install the ball and compression spring onto the transmission rear case.
Install a new shift detent ball plug, and install it onto the transmission rear case.
| 32. INSTALL OUTPUT SHAFT ADJUST NUT |
![]() |
Using a belt and wooden block, fasten the transmission to the workbench.
Install a new spacer and output shaft taper roller bearing No. 2.
![]() |
Using a socket wrench (60 mm), provisionally tighten a new nut until there is no slack in the output shaft.
Fit the bearing into the output shaft by turning the output shaft 15 times.
![]() |
Place the gearshift into 5th gear and check the initial torque of the input shaft.
Using a socket wrench (60 mm), tighten the nut.
Place the gearshift into 5th gear and check the initial torque of the input shaft.
Confirm that the difference between (f) and (i) is within the specified values.
![]() |
Using a chisel and hammer, caulk the output shaft adjust nut.
| 33. INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
![]() |
Apply FIPG to the transmission case cover, as shown in the illustration.
![]() |
Install the transmission case cover with the 4 bolts.
| 34. INSTALL SHIFT LEVER HOUSING |
![]() |
Install the shift lever housing with the bolt.
| 35. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY |
![]() |
Apply FIPG to the floor shift control shift lever retainer, as shown in the illustration.
![]() |
Install the floor shift control shift lever retainer with the 4 bolts.