TOWING CONVERTER RELAY > REMOVAL |
| 1. BOLT, SCREW AND NUT TABLE |

| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 2 clips and remove the front floor footrest.
| 4. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Disengage the 8 claws and clip, and remove the front door scuff plate.
| 5. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab) |
![]() |
Disengage the 9 claws and clip, and remove the front door scuff plate.
| 6. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab) |
| 7. REMOVE FRONT DOOR SCUFF PLATE RH (for Regular Cab) |
| 8. REMOVE FRONT DOOR SCUFF PLATE RH (for Access Cab) |
| 9. REMOVE FRONT DOOR SCUFF PLATE RH (for Double Cab) |
| 10. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 11. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 12. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 13. REMOVE COWL SIDE TRIM BOARD RH (for Regular Cab) |
| 14. REMOVE COWL SIDE TRIM BOARD RH (for Access Cab) |
| 15. REMOVE COWL SIDE TRIM BOARD RH (for Double Cab) |
| 16. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Separate the front door opening trim weatherstrip LH.
| 17. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Separate the front door opening trim weatherstrip RH.
| 18. REMOVE FRONT PILLAR GARNISH LH (for Regular Cab) |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.
![]() |
Remove the 2 screws.
Disengage the clip and claw and remove the front pillar garnish.
![]() |
for LH Side:
Using a clip remover, remove the 3 wire harness clamps.
| 19. REMOVE FRONT PILLAR GARNISH LH (for Access Cab) |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.
![]() |
Remove the 2 screws.
Disengage the claw and clip, and remove the front pillar garnish.
![]() |
for LH Side:
Using a clip remover, remove the 3 wire harness clamps.
| 20. REMOVE FRONT PILLAR GARNISH LH (for Double Cab) |
![]() |
Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug.
![]() |
Remove the 2 screws.
Disengage the clip and claw and remove the front pillar garnish.
![]() |
for LH side:
Using a clip remover, remove the 3 wire harness clamps.
![]() |
w/ Curtain Shield Airbag:
Thoroughly cover the air bag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 21. REMOVE FRONT PILLAR GARNISH RH (for Regular Cab) |
| 22. REMOVE FRONT PILLAR GARNISH RH (for Access Cab) |
| 23. REMOVE FRONT PILLAR GARNISH RH (for Double Cab) |
| 24. REMOVE INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) |
![]() |
Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.
| 25. REMOVE INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) |
![]() |
Disengage the 4 clips and remove the instrument panel hole cover.
| 26. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type) |
![]() |
Remove the shift knob.
Disengage the 6 clips and claw, and remove the console upper rear panel sub-assembly.
| 27. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type) |
![]() |
Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.
| 28. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type) |
![]() |
Remove the console box carpet.
![]() |
Remove the 2 screws <F> and 2 bolts <B>.
Disengage the 4 claws and remove the rear console box assembly.
| 29. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type) |
![]() |
Disengage the 2 clips and 4 claws, and remove the instrument panel cup holder tray.
| 30. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type) |
![]() |
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 31. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type) |
![]() |
Remove the shift knob.
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 32. REMOVE FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 33. REMOVE FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type) |
![]() |
Remove the shift knob.
Remove the box bottom mat.
Remove the instrument panel cup holder.
Remove the No. 2 box bottom mat.
![]() |
Remove the clip and 2 bolts <A>.
Disengage the 2 clips and claw, and remove the front console box.
| 34. REMOVE AIR CONDITIONING CONTROL ASSEMBLY |
![]() |
Using a screwdriver, disengage the 4 clips and remove the air conditioning control assembly.
Disconnect the 2 connectors.
| 35. REMOVE RADIO RECEIVER ASSEMBLY |
![]() |
Remove the 4 bolts.
Disconnect the connector and remove the radio receiver assembly with bracket.
| 36. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 2 claws.
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.
| 37. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINFISH PANEL |
![]() |
Remove the 2 bolts <B>.
Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.
Disconnect the connectors.
| 38. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disengage the 6 clips and remove the instrument cluster finish panel sub-assembly.
Disconnect the connectors.
| 39. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws <E> and the combination meter assembly.
Disconnect the 2 connectors.
| 40. REMOVE INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Disengage the 10 clips and remove the instrument cluster center finish panel sub-assembly.
| 41. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Disengage the claw and separate the glove compartment door stopper from the glove compartment door assembly.
Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
![]() |
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.
| 42. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH |
![]() |
Remove the bolt <B>.
Disengage the 2 clips and remove the instrument panel lower finish panel sub-assembly RH.
| 43. REMOVE LOWER INSTRUMENT PANEL LH |
![]() |
Remove the 3 bolts <B> and the lower instrument panel LH.
| 44. REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY |
![]() |
Remove the bolt <B>.
Disengage the 5 clips and remove the instrument lower cover sub-assembly.
Disconnect the 2 connectors.
| 45. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using a screwdriver, disengage the 3 claws and remove the instrument side panel RH.
| 46. DISCONNECT PASSENGER AIRBAG CONNECTOR |
![]() |
Disconnect the airbag connector.
| 47. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY W/ PASSENGER AIRBAG ASSEMBLY |
![]() |
Tape up the steering column cover upper and steering wheel sub-assembly in protective tape.
Disengage the 4 clamps and disconnect the 4 connectors.
Remove the 8 bolts, nut and instrument panel sub-assembly w/ passenger air bag assembly.

| 48. REMOVE TOWING CONVERTER RELAY |
![]() |
Disconnect the connector.
Remove the bolt and towing converter relay.