ENGINE UNIT > REASSEMBLY |
| 1. INSTALL STUD BOLT |
Install the stud bolts as shown in the illustration.

| 2. INSTALL STRAIGHT PIN |
Using a plastic-faced hammer, tap into the new straight pin.

| 3. INSTALL TIGHT PLUG |
Apply adhesive around tight plugs.
Using SST, install the tight plugs as shown in the illustration.

| 4. INSTALL OIL JET |
![]() |
Using a screw driver and hammer, tap in a oil jet.
| 5. INSTALL NO.1 SUB-ASSEMBLY OIL NOZZLE |
![]() |
Using a 5 mm socket hexagon wrench, install the 3 oil nozzles.
| 6. INSTALL HOLE SNAP RING |
![]() |
Using a small screwdriver, install a new snap ring onto one side of the piston pin hole.
| 7. INSTALL WITH PIN PISTON SUB-ASSEMBLY |
![]() |
Gradually heat the piston to about 80°C (176°F).
![]() |
Coat the piston pin with engine oil.
Align the front marks of the piston and connecting rod, and push in the piston pin with thumb.
| 8. INSTALL HOLE SNAP RING |
![]() |
Using a small screwdriver, install a new snap ring onto the other side of the piston pin hole.
| 9. INSTALL PISTON RING SET |
![]() |
Install the oil ring expander and 2 side rails by hand.
Using a piston ring expander, install the 2 compression rings.
![]() |
Position the piston rings so that the ring ends are as shown.
| 10. INSTALL CONNECTING ROD BEARING |
![]() |
Align the bearing claw with the groove of the connecting rod or connecting cap.
| 11. INSTALL CRANKSHAFT BEARING |
![]() |
Clean each main journal and bearing.
![]() |
Install the 4 upper bearings.
Install the upper bearings near the center of the cylinder block.
![]() |
Install the 4 lower bearings.
Install the lower bearings near the center of the cylinder block.
| 12. INSTALL CRANKSHAFT |
Apply engine oil to the upper bearing and install the crankshaft onto the cylinder block.
![]() |
Install the 2 upper thrust washers onto the No. 2 journal position of the cylinder block.
Push the crankshaft toward the front (rear) side.
Install the 2 upper thrust washers with the oil grooves facing outward.
![]() |
Install the 2 lower thrust washers onto the No. 2 bearing cap with the grooves facing outward.
![]() |
Examine the front marks and numbers, check the sequence number is as shown in the illustration and install the bearing caps on the cylinder block.
Apply a light coat of engine oil to the threads of bearing cap bolts.
Temporarily install the 8 main bearing cap bolts in the inside positions.
![]() |
Install the main bearing caps. Tighten the 2 bolts for each bearing cap until the clearance between the bearing cap and the cylinder block is under 6 mm (0.23 in.).
![]() |
Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.
Apply a light coat of engine oil to the threads of main bearing cap bolts.
![]() |
Install the 16 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.
![]() |
Mark the front side of the bearing cap bolts with paint.
Retighten the bearing cap bolts 90° in the sequence as shown.
Check that the painted mark is now at a 90° angle from the front.
Check that the crankshaft turns smoothly.
![]() |
Using several steps, tighten the 8 main bearing cap bolts uniformly in the sequence shown in the illustration.
| 13. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTIONG ROD |
![]() |
Apply engine oil to the cylinder walls, pistons, and surfaces of connecting rod bearings.
Check the position of the piston ring ends.
Using a piston ring compressor, push the correct number piston and connecting rod into each cylinder with the front mark of the piston facing forward.
![]() |
Check that the protrusion of the connecting rod cap is facing in the correct direction.
Apply a light coat of engine oil to the threads of the connecting rod cap bolts.
![]() |
Using SST, tighten the bolts alternately to the specified torque.
![]() |
Mark the front side of the each connecting cap bolt with paint.
Retighten the cap bolts 90° as shown.
Check that the crankshaft turns smoothly.
| 14. INSTALL RING PIN |
Using a plastic-faced hammer, tap in the new ring pins to the specified protrusion height.

| 15. INSTALL STRAIGHT PIN |
Using a plastic-faced hammer, tap in the new straight pins to the specified protrusion height.
| A | 17.5 to 19.5 mm (0.689 to 0.768 in.) |
| B | 7.5 to 8.5 mm (0.295 to 0.335 in.) |
| C | 7.0 to 9.0 mm (0.276 to 0.354 in.) |

| 16. INSTALL STUD BOLT |
Using the torx socket wrenchs E5 and E7, install the stud bolts.

| 17. INSTALL UNION |
![]() |
Apply adhesive to 2 or 3 threads of the bolt end.
Using a deep socket wrench 12, install the unions.

| 18. INSTALL TIGHT PLUG |
![]() |
Apply adhesive around the tight plug.
Using SST, tap in the tight plugs to the specified depth.

| 19. INSTALL WITH HEAD STRAIGHT SCREW PLUG |
Using a straight hexagon wrench 14, install a new gasket and straight screw plug.

| 20. INSTALL VALVE STEM OIL O SEAL OR RING |
![]() |
Apply a light coat of engine oil to the valve guide bush.
![]() |
Using SST, push in a new valve stem oil seal.
| 21. INSTALL VALVE SPRING SEAT |
![]() |
| 22. INSTALL VALVE |
![]() |
Apply the engine oil to the valve as shown in the illustration.
![]() |
Place the cylinder head on a wooden block.
Install the valve, inner compression spring and valve spring retainer.
Using SST, compress the inner compression spring and place the 2 valve spring retainer rocks around the valve stem.
![]() |
Using a pin punch 5, lightly tap the valve stem tip to ensure a proper fit.
| 23. INSTALL VALVE LIFTER |
![]() |
Apply the engine oil to the valve stem end and valve lifter, and install the valve lifter onto the valve stem.
Check that the valve lifter rotates smoothly by hand.
| 24. INSTALL REAR ENGINE OIL SEAL RETAINER |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the oil seal retainer and cylinder block.
![]() |
Apply a continuous bead of seal packing (diameter 2 to 3 mm (0.08 to 0.12 in.)) to the oil seal retainer as shown in the illustration.
Install the oil seal retainer with the 5 bolts and 2 nuts.
| 25. INSTALL KNOCK CONTROL SENSOR |
![]() |
Install the 2 knock sensors with the 2 bolts as shown in the illustration.
Connect the knock sensor connectors.
Connect the knock sensor wire.
| 26. INSTALL NO.1 WATER OUTLET PIPE |
![]() |
Install the water outlet pipe with the 3 bolts.
| 27. INSTALL CYLINDER HEAD GASKET |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder head and cylinder block.
![]() |
Apply a continuous bead of seal packing (diameter 2.5 to 3 mm (0.098 to 0.118 in.)) to a new cylinder head gasket as shown in the illustration.
![]() |
Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.
| 28. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the RH cylinder head on the cylinder head gasket.
Install the 8 cylinder head bolts.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
![]() |
Using several steps, uniformly install and tighten the 10 cylinder head bolts and plate washers with a bi-hexagon wrench 10 mm in the sequence shown in the illustration.
![]() |
Mark the front of the cylinder head bolt with paint.
Retighten the cylinder head bolts by 180° as shown.
Check that the painted marks are now at 180° from the engine front.
| 29. INSTALL NO.2 CYLINDER HEAD GASKET |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder head and cylinder block.
![]() |
Apply a continuous bead of seal packing (Diameter 2.5 to 3 mm (0.098 to 0.118 in.)) to a new cylinder head gasket as shown in the illustration.
![]() |
Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.
| 30. INSTALL CYLINDER HEAD LH |
Place the LH cylinder head on the cylinder head gasket.
Install the 8 cylinder head bolts.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
![]() |
Using several steps, uniformly install and tighten the 8 cylinder head bolts and plate washers with a bi-hexagon wrench 10 mm in the sequence shown in the illustration.
![]() |
Mark the front of the cylinder head bolt with paint.
Retighten the cylinder head bolts by 180° as shown.
Check that the painted marks are now at 180° from the engine front.
![]() |
Install the 2 cylinder head bolts.
Apply a light coat of engine oil to the threads of the cylinder head bolts.
Using several steps, uniformly install and tighten the 10 cylinder head bolts and plate washers with a bi-hexagon wrench 10 mm in the sequence shown in the illustration.
| 31. INSTALL NO.1 CAMSHAFT BEARING |
![]() |
Align the bearing claw with the claw groove of the bearing cap, and push in the camshaft bearing.
| 32. INSTALL NO.2 CAMSHAFT BEARING |
![]() |
Install camshaft bearing No. 2 onto the cylinder head.
| 33. INSTALL CAMSHAFTS |
![]() |
Set the crankshaft position.
Using the crankshaft pulley set bolt, turn the crankshaft, and set the crankshaft set key in the left horizontal position as indicated.
Apply new engine oil to the thrust portion and journal of the camshafts.
![]() |
Install the camshaft of the RH bank.
Place the 2 camshafts on the RH cylinder head with the No. 1 cam lobes facing as shown the illustration.
![]() |
Install the 8 bearing caps in their correct locations.
Apply a light coat of engine oil to the threads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 16 bearing cap bolts in the sequence shown in the illustration.
![]() |
Using a wrench, turn the camshafts clockwise until each camshaft knock pin comes to a position 90° to the cylinder head.
![]() |
Install the camshafts of the LH bank.
Place the 2 camshafts on the LH cylinder head with the No.1 cam lobes facing as shown the illustration.
![]() |
Install the 8 bearing caps in the correct locations as shown.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 16 bearing cap bolts in the sequence shown in the illustration.
| 34. INSTALL NO.2 CHAIN TENSIONER ASSEMBLY |
![]() |
While pushing in the tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Install the chain tensioner No. 2 with the bolt.
| 35. INSTALL CAMSHAFT TIMING GEARS AND NO.2 CHAIN (for Bank 1) |
![]() |
Align the yellow mark links with the timing marks (1 dot mark) of camshaft timing gears as shown in the illustration.
![]() |
Align the timing marks on the camshaft timing gears with the timing marks on the bearing caps, and install the camshaft timing gears with the chain onto the RH camshafts.
Temporarily install the 2 camshaft timing gear bolts.
![]() |
Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.
Remove the pin from the chain tensioner No. 2.
| 36. INSTALL NO.3 CHAIN TENSIONER ASSEMBLY |
![]() |
While pushing in the tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to hold it.
![]() |
Install the chain tensioner No. 3 with the bolt.
| 37. INSTALL CAMSHAFT TIMING GEARS AND NO.2 CHAIN (for Bank 2) |
![]() |
Align the yellow mark links with the timing marks (1 dot mark and 2 dot marks) on camshaft timing gears as shown in the illustration.
![]() |
Align the timing marks on the camshaft timing gears with the timing marks on the bearing caps, and install the camshaft timing gears with the chain onto the LH camshafts.
Temporarily install the 2 camshaft timing gear bolts.
![]() |
Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.
Remove the pin from the chain tensioner No. 3.
| 38. INSTALL NO.1 CHAIN VIBRATION DAMPER |
![]() |
Install the chain vibration damper No. 1 with the 2 bolts.
| 39. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Align the timing gear set key with the key groove of the timing gear.
Install the timing gear onto the crankshaft with the gear side facing inward.
| 40. INSTALL CHAIN TENSIONER SLIPPER |
| 41. INSTALL NO.1 CHAIN TENSIONER ASSEMBLY |
![]() |
While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.
While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.
Install the chain tensioner with the 2 bolts.
| 42. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
Set the No. 1 cylinder to TDC/ compression.
Align the timing marks of the camshaft timing gears and bearing caps.
![]() |
Using the crankshaft pulley set bolt, turn the crankshaft to align the crankshaft set key with the timing line of the cylinder block.
![]() |
Align the yellow mark link with the timing mark of the crankshaft timing gear.
![]() |
Align the orange mark links with the timing marks of the camshaft timing gears, and install the chain.
| 43. INSTALL NO.2 CHAIN VIBRATION DAMPER |
![]() |
Instal the 2 chain vibration dampers No. 2.
| 44. INSTALL IDLE SPROCKET ASSEMBLY |
Apply a light coat of engine oil to rotating surface of the idle gear shaft No. 1.
![]() |
Temporarily install the idle gear shaft No. 1 together with the idle gear shaft No. 2 while aligning the knock pin of the idle gear shaft No. 1 with the knock pin groove of the cylinder block.
Using a 10 mm hexagon wrench, tighten the idle gear shaft No. 2.
Remove the bar from the chain tensioner.
| 45. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
![]() |
Install a new O-ring onto the LH cylinder head as shown in the illustration.
![]() |
Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to 4 locations as shown in the illustration.
![]() |
Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the timing chain cover as shown in the illustration.
![]() |
Align the key way of the oil pump drive rotor with the rectangular portion of the crankshaft timing gear, and slide the timing chain cover into place.
![]() |
Install the timing chain cover with the 15 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| Bolt | length |
| A | 25 mm (0.98 in.) |
| B | 55 mm (2.17 in.) |
| 46. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the water pump with the 17 bolts.
| 47. INSTALL OIL PAN SUB-ASSEMBLY |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.
![]() |
Install the 4 stud bolts (for 2WD).
![]() |
Install the 4 stud bolts (for Pre Runner and 4WD).
![]() |
Install a new O-ring onto the oil pump.
![]() |
Apply a continuous bead of seal packing (diameter 3 to 4 mm (0.12 to 1.16 in.)) to the oil pan as shown in the illustration (for 2WD).
![]() |
Apply a continuous bead of the seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) to the oil pan as shown in the illustration (for Pre Runner and 4WD).
![]() |
Install the oil pan with the 17 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps (for 2WD).
| Bolt | length |
| A | 25 mm (0.98 in.) |
| B | 45 mm (1.77 in.) |
| C | 14 mm (0.55 in.) |
![]() |
Install the oil pan with the 17 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps (for Pre Runner and 4WD).
| Bolt | length |
| A | 25 mm (0.98 in.) |
| B | 45 mm (1.77 in.) |
| C | 14 mm (0.55 in.) |
| 48. INSTALL OIL STRAINER SUB-ASSEMBLY |
![]() |
Install a new gasket, then install the oil strainer with the 2 nuts (for 2WD).
![]() |
Install a new gasket, then install the oil strainer with the 2 nuts (for Pre Runner and 4WD).
| 49. INSTALL NO.2 OIL PAN SUB-ASSEMBLY |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the oil pan and oil pan No. 2.
![]() |
Apply a continuous bead of the seal packing (diameter 3 to 4 mm (0.12 to 0.16 in.)) as shown in the illustration (for 2WD).
![]() |
Apply a continuous bead of seal packing (diameter 3 to 4mm(0.12 to 0.16 in.)) as shown in the illustration (for Pre Runner and 4WD).
![]() |
Install the oil pan No. 2 with the 15 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps (for 2WD).
![]() |
Install the oil pan No. 2 with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps (for Pre Runner and 4WD).
| 50. INSTALL OIL PAN DRAIN PLUG |
Install the drain plug with a new gasket.
| 51. INSTALL CRANKSHAFT PULLEY |
![]() |
Using SST, fix the pulley and tighten the bolt.
| 52. SET NO.1 CYLINDER TO TDC/COMPRESSION |
| 53. INSPECT VALVE CLEARANCE |
| 54. ADJUST VALVE CLEARANCE |
| 55. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.
Install the gasket onto the cylinder head cover.
![]() |
Apply a continuous bead of seal packing (diameter 2 to 3 mm (0.08 to 0.12 in.)) to the cylinder head and timing chain cover as shown in the illustration.
Install the seal washers onto the bolts.
![]() |
Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| Bolt | length |
| A | 25 mm |
| B | 60 mm (2.36 in.) |
| 56. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.
Apply adhesive to the threads of the ventilation valve.
Install the ventilation valve onto the cylinder head cover.
Install the gasket onto the cylinder head cover.
![]() |
Apply a continuous bead of seal packing (diameter 2 to 3 mm (0.08 to 0.12 in.)) to the cylinder head and timing chain cover as shown in the illustration.
Install the seal washers onto the bolts.
![]() |
Install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| Bolt | length |
| A | 25 mm (0.98 in.) |
| B | 60 mm (2.36 in.) |
| 57. INSTALL OIL CONTROL VALVE FILTER |
![]() |
Check that no foreign objects on the mesh part of the 2 filters.
Install 2 new gaskets onto each new plug.
Insert the filters into the plugs.
Apply adhesive to 2 or 3 threads of the plugs.
Install the plugs onto each cylinder head.
| 58. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Install the crankshaft position sensor with the bolt.
| 59. INSTALL VVT SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring of each VVT sensor.
Install the 2 VVT sensors with the 2 bolts.
| 60. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the drain cocks end.
![]() |
Tighten the drain cocks to the specified torque, and rotate them clockwise as shown in the illustration.
| 61. INSTALL OIL LEVEL GAGE GUIDE |
![]() |
Install a new O-ring onto the oil level gauge guide.
Apply a light coat of engine oil to the O-ring.
Push the oil level gauge guide end into the guide hole of the oil pan.
Install the oil level gauge guide with the bolt.
| 62. INSTALL ENGINE HANGERS |
![]() |
Install the engine hanger with the 2 bolts.
Install the engine hanger with the 2 bolts.