Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > INSTALLATION

for Preparation Click here



1. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY


G037326E01
  1. Put the camshaft timing gear and camshaft together by aligning the key groove and straight pin.

  1. Gently press the gear against the camshaft, and turn the gear. Push further at the position where the pin fits into the groove.

    CAUTION:
    Be sure not to turn the camshaft timing gear to the retard angle side (to the right angle).

  1. Check that there is no clearance between the gear's fringe and the camshaft.

  1. Tighten the fringe bolt with the camshaft timing gear fixed.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Check that the camshaft timing gear can move to the retard angle side (the right angle), and is locked in the extreme retard position.



2. INSTALL CAMSHAFT


A115992E01

NOTICE:
Check that the valve rocker arm is correctly set as shown in the illustration.

  1. Apply clean engine oil to the camshaft's cam portion and the cylinder head journals.

  1. Install the chain onto the camshaft timing gear, with the painted mark of the link aligned with the timing mark of the camshaft timing gear.



    A097874E01
  1. Set the 2 camshafts as shown in the illustration.

    NOTICE:
    Align the paint mark with the timing mark before setting the camshaft.



    G037331E03
  1. Provisionally install the No. 1 camshaft bearing cap.

  1. Check the proper location of each No. 2 camshaft bearing cap and install each one.



    G037284E05
  1. Install a new O-ring onto the No. 1 camshaft bearing cap.

  1. Provisionally install the camshaft oil delivery pipe.



    G038225E02
  1. Tighten the bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for bolt A
    16 N*m{ 158 kgf*cm , 11 ft.*lbf } for bolts except bolt A



    A097877E03
  1. Check that each timing mark is set in the position shown in the illustration.



    A097878E04
  1. Install the timing chain onto the camshaft timing gear, with the paint mark aligned with the timing mark on the camshaft timing gear.

  1. Align the No. 2 camshaft straight pin and camshaft timing gear straight pin hole. Then install the camshaft timing gear onto the No. 2 camshaft.

    NOTICE:
    If the straight pin and straight pin hole are difficult to align, slightly rotate the No. 2 camshaft to the left and right using the hexagonal lobe of the camshaft. Then attempt to align them again.



    A097863E05
  1. Hold the hexagonal lobe of the No. 2 camshaft with the adjustable wrench.

  1. Tighten the bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Remove the 3.0 mm (0.118 in.) diameter bar from the chain tensioner.

  1. Apply adhesive to 2 or 3 threads of the timing gear case with head straight screw plug.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent



    A086539E01
  1. Using a 10 mm socket hexagon wrench, install the timing gear case with head straight screw plug.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }



3. INSTALL TIMING CHAIN GUIDE


G038218E01
  1. Install a new O-ring onto the camshaft bearing cap.



    G038217E01
  1. Install the timing chain guide with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



4. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


A097879E03
  1. Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes of applying the seal packing.
    3. Do not apply engine oil for at least 2 hours of installation.



    G035202E06
  1. Provisionally install the cylinder head cover with the 19 bolts and 2 nuts.

  1. Tighten bolts A shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Tighten bolts B and nuts shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Tighten bolts A again.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    G038216E01
  1. Connect the ventilation hose.



    G038215E01
  1. Install the ignition coils with the bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    G038214E01
  1. Install the engine wire harness clamps.

  1. Connect the camshaft position sensor connector.

  1. Connect the VSV connector.

  1. Connect the throttle with motor body connector.

  1. Connect the ignition coil connectors.



5. INSTALL INTAKE AIR CONNECTOR


    G037697E01
  1. Install the intake air connector with the 3 bolts.

    Torque:
    8 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts.

    Torque:
    5 N*m{ 51 kgf*cm , 44 in.*lbf }



    G037696E01
  1. Connect the vacuum hose.



    G037695E01
  1. Connect the ventilation hose No. 2.



    G037694E01
  1. Connect the vacuum hose.

  1. Engage the wire harness clamp.

  1. Connect the pressure sensor connector.



6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


G037934E01
  1. Install the air cleaner cap together with the air cleaner hose No. 1.

  1. Connect the 2 air cleaner clamps.

  1. Tighten the hose clamp bolt, then connect the air cleaner hose No. 1.

  1. Connect the wire harness clamp.

  1. Connect the mass air flow meter connector.



7. INSTALL FAN SHROUD


G038211E02
  1. Install the fan pulley.



    G038210E02
  1. Install the fan shroud and fan with fluid coupling together.

    NOTICE:
    Make sure that the fan shroud and fan with fluid coupling do not make any contact with the radiator when they are installed.

  1. Provisionally install the fan with fluid coupling with the 4 nuts.



    G038564E01
  1. Install the 2 bolts shown in the illustration.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    G038208E02
  1. Connect the oil cooler inlet and outlet hoses to the fan shroud. (for Automatic Transmission)



    G038207E02
  1. Connect the radiator reserve tank hose to the radiator.

  1. Install the fan generator V belt.



    A086838E02
  1. Tighten the 4 nuts shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



8. INSTALL RADIATOR SUPPORT TO FRAME SEAL LH


G038206E01
  1. Install the radiator support frame seal LH with the 9 clips.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



10. ADD ENGINE COOLANT
  1. Tighten the engine drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain plug.

  1. Disconnect the 2 vinyl hoses.

  1. Slowly fill the system with engine coolant.

    Capacity:
    M/T: 8.7 liters (9.2 US qts, 7.7 lmp. qts)
    A/T: 8.6 liters (9.1 US qts, 7.6 lmp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids.)
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)) is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except OFF
    Temperature
    Toward warm
    Air condition switch
    OFF

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warning up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (d) through (k) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.

  1. Install the engine under cover No. 1 with the 4 bolts. (PRE RUNNER AND 4WD TYPE)

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



11. CHECK FOR ENGINE COOLANT LEAKAGE


G038195E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Fluid and steam could be blown out under pressure.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it up to 118 kPa (1.2 kgf/cm2, 17.1 psi) and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hose, radiator and water pump for leakage. If no external leakage is found, check the heater core, cylinder block and cylinder head.



12. CHECK FOR ENGINE OIL LEAKAGE


13. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type)
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }