ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
![]() |
Remove the oil filler cap sub-assembly.
| 2. REMOVE VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Remove the ventilation valve sub-assembly.
| 3. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the bolt and camshaft position sensor.
| 4. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the bolt and crankshaft position sensor.
| 5. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Remove the bolt and camshaft timing oil control valve.
| 6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.
| 7. REMOVE CRANKSHAFT PULLEY |
![]() |
Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.
Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the bearing cap No.1, as shown in the illustration.
![]() |
Using SST, loosen the crankshaft pulley bolt.
![]() |
Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
| 8. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the drain plug and gasket.
Remove the 18 bolts and 2 nuts.
![]() |
Insert the blade of SST between the oil pans. Cut through the applied sealer and remove the oil pan sub-assembly No.2.
| 9. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 2 bolts, 2 nuts, oil strainer and gasket.
| 10. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
![]() |
Remove the O-ring.
| 11. REMOVE TIMING CHAIN COVER |
![]() |
Remove the 19 bolts and 2 nuts as shown in the illustration.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
![]() |
Remove the 3 O-rings.
![]() |
Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.
| 12. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 8 bolts, water pump and gasket.
| 13. REMOVE TIMING CHAIN GUIDE |
![]() |
Remove the 2 bolts, timing chain guide and O-ring.
| 14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate's hole.
![]() |
Remove the bolt, nut, chain tensioner assembly No.1 and gasket.
| 15. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
Remove the bolt and tensioner slipper.
| 16. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the bolt, nut, and vibration damper.
| 17. REMOVE CHAIN SUB-ASSEMBLY |
Remove the chain.
| 18. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Remove the crankshaft timing gear from the crankshaft.
| 19. REMOVE CAMSHAFT BEARING CAP |
![]() |
Uniformly loosen and remove the 21 bearing cap bolts and 20 washers on the camshafts in the sequence shown in the illustration.
![]() |
Remove the oil delivery pipe and O-ring from the bearing caps.
![]() |
Remove the 9 bearing caps.
| 20. REMOVE CAMSHAFT |
![]() |
Remove the camshaft sub-assembly.
| 21. REMOVE NO.2 CAMSHAFT |
![]() |
Remove the No.2 camshaft sub-assembly.
| 22. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Remove the 16 valve rocker arm sub-assembly.
| 23. REMOVE CAMSHAFT TIMING SPROCKET |
![]() |
Fix the camshaft with a vise and then remove the sprocket bolt and camshaft timing sprocket.
| 24. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Check the lock of the camshaft timing gear.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path and the retard side path on the opposite side to the hole of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf*cm2, 28 psi) of air pressure to the two broken paths.
![]() |
Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.
When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.
Check for smooth rotation.
Rotate the camshaft timing gear within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear is locked at the most retarded position.
| 25. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Remove the fringe bolt and camshaft timing gear.
| 26. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.
Remove the cylinder head.
| 27. REMOVE CYLINDER HEAD GASKET |
Remove the cylinder head and gasket.
| 28. REMOVE NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Move the stopper plate downward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate upward to set the lock, and insert a hexagon wrench into the stopper plate's hole.
![]() |
Remove the bolt and chain vibration damper No.2.
| 29. REMOVE NO. 3 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and chain vibration damper No.3.
| 30. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the hexagon wrench from the tensioner assembly No.2.
Remove the nut and chain tensioner assembly No.2.
| 31. REMOVE NO.2 CHAIN SUB-ASSEMBLY |
![]() |
Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear.
Remove the crankshaft timing sprocket No.2 and chain.
| 32. REMOVE NO. 4 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and vibration damper No.4.
| 33. REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY |
![]() |
Remove the 2 pulley set keys from the crankshaft.
| 34. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
![]() |
Using a 27 mm socket wrench, remove the oil filter union.
| 35. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and nut from the oil filter bracket.
Remove the 2 screw plugs and 2 gaskets from the oil filter bracket.
![]() |
Remove the oil filter bracket gasket and O-ring.
![]() |
Using a hexagon wrench, remove the oil filter bracket union.
| 36. REMOVE NO. 1 WITH HEAD TAPER SCREW PLUG |
![]() |
Remove the taper screw plug from the cylinder block.
| 37. REMOVE ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove the 6 bolts.
Using a screwdriver with its tip taped, pry out the oil seal retainer.
| 38. REMOVE VALVE STEM CAP |
![]() |
Remove the valve stem caps from the cylinder head.
| 39. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
![]() |
Remove the valve lash adjusters from the cylinder head.
| 40. REMOVE INTAKE VALVE |
![]() |
Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
![]() |
Remove the retainer, compression spring, and valve.
| 41. REMOVE EXHAUST VALVE |
![]() |
Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
![]() |
Remove the retainer, compression spring, and valve.
| 42. REMOVE VALVE STEM OIL SEAL |
![]() |
Using needle-nose pliers, remove the oil seals.
| 43. REMOVE VALVE SPRING SEAT |
Remove the valve spring seats from the cylinder head.
| 44. REMOVE OIL CONTROL VALVE FILTER |
![]() |
Using an 8 mm hexagon wrench, remove the screw plug.
Remove the oil control valve filter and gasket.
| 45. REMOVE NO. 1 WITH HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm hexagon wrench, remove the 3 screw plugs and 3 gaskets.
| 46. REMOVE NO. 2 WITH HEAD STRAIGHT SCREW PLUG |
![]() |
Using a 19 mm hexagon wrench, remove the screw plug and gasket.
| 47. REMOVE CRANKSHAFT BEARING |
| 48. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 49. REMOVE CONNECTING ROD BEARING |
| 50. REMOVE CRANKSHAFT |
![]() |
Uniformly loosen the 10 bearing cap bolts, in several steps, in the sequence shown in the illustration.
Lift out the crankshaft.
![]() |
Remove the upper bearings and upper thrust washers from the cylinder block.
| 51. REMOVE CRANKSHAFT BEARING |
| 52. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the 2 compression rings.
Using a piston ring expander, remove the oil ring rail.
Remove the oil ring expander by hand.
| 53. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Remove the water drain cock sub-assembly from the cylinder block.
Remove the water drain cock plug from the water drain cock sub-assembly.
| 54. REMOVE WITH PIN PISTON SUB-ASSEMBLY |
![]() |
Check the fitting condition between the piston and piston pin.
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
![]() |
Disconnect the connecting rod from the piston.
Using a screwdriver, pry off the snap rings from the piston.
![]() |
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
![]() |
Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.
| 55. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, remove the oil nozzles.
| 56. REMOVE NO.1 BALANCESHAFT |
![]() |
Remove the bolt.
![]() |
Remove the balanceshaft from the cylinder block.
| 57. REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR |
![]() |
Mount the head portion of the balanceshaft in a vise.
Remove the bolt.
Remove the balanceshaft driven gear No.1 (*1), sliding key (*2), balanceshaft thrust washer No.1 (*3) and balanceshaft thrust spacer (*4).
| 58. REMOVE NO.2 BALANCESHAFT |
![]() |
Remove the 2 bolts.
![]() |
Remove the balanceshaft from the cylinder block.
| 59. REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR |
![]() |
Mount the head portion of the balanceshaft in a vise.
Remove the bolt.
Remove the balanceshaft driven gear No.2 (*1) and balanceshaft thrust washer No.2 (*2).