DTC B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction |
DTC B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction |
| DTC No. | DTC Detecting Conditions | Trouble Areas |
| B1620/21 |
|
|
| B1625/22 |
|
|

| 1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
Check the DTC (Click here.
| Result | Proceed to |
| DTC B1620/21 is output. | A |
| DTC B1625/22 is output. | B |
| DTC B1620/21 and B1625/22 are output. | C |
| Neither DTC B1620/21 nor B1625/22 is output. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly LH.
Using SST, connect S11-4 (BBL+) and S11-3 (BBL-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - A22-15 (BBD-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - A22-15 (BBD-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 6.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - Body ground | Ignition switch ON | Below 1 V |
| A22-15 (BBD-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - Body ground | Always | 1 MΩ or Higher |
| A22-15 (BBD-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 8.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn any ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1620/21 is output. | A |
| DTC B1625/22 is output. | B |
| Neither DTC B1620/21 nor B1625/22 is output. | C |
|
| ||||
|
| ||||
| A | |
| 9.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the rear airbag sensor LH.
|
| ||||
| OK | |
| 10.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 11.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.
Using SST, connect S13-1 (BCL-) and S13-2 (BCL+) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 12.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 13.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| S11-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 14.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Always | 1 MΩ or Higher |
| S11-2 (BCL-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 15.CHECK DTC |
![]() |
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 16.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 17.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
|
| ||||
| OK | |
| 18.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 19.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly RH.
Using SST, connect S12-4 (BBR+) and S12-3 (BBR-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - A23-11 (BBP-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 20.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - A23-11 (BBP-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 21.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - Body ground | Ignition switch | Below 1 V |
| A23-11 (BBP-) - Body ground | Ignition switch | Below 1 V |
|
| ||||
| OK | |
| 22.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - Body ground | Always | 1 MΩ or Higher |
| A23-11 (BBP-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1625/22 is output. | A |
| DTC B1620/21 is output. | B |
| Neither DTC B1620/21 nor B1625/22 is output. | C |
|
| ||||
|
| ||||
| A | |
| 24.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
|
| ||||
| OK | |
| 25.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly RH side and rear airbag sensor RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 26.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.
Using SST, connect S14-1 (BCR-) and S14-2 (BCR+) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 27.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 28.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| S12-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 29.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Always | 1 MΩ or Higher |
| S12-2 (BCR-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 30.CHECK DTC |
![]() |
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 31.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 32.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.
|
| ||||
| OK | |
| 33.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 34.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly LH.
Using SST, connect S11-4 (BBL+) and S11-3 (BBL-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - A22-15 (BBD-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 35.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - A22-15 (BBD-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 36.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - Body ground | Ignition switch ON | Below 1 Ω |
| A22-15 (BBD-) - Body ground | Ignition switch ON | Below 1 Ω |
|
| ||||
| OK | |
| 37.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
![]() |
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A22-8 (BBD+) - Body ground | Always | 1 MΩ or Higher |
| A22-15 (BBD-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 38.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the rear airbag sensor LH.
|
| ||||
| OK | |
| 39.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 40.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.
Using SST, connect S13-1 (BCL-) and S13-2 (BCL+) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 41.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - S11-2 (BCL-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 42.CHECK NO. 2 FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Ignition switch ON | Below 1 Ω |
| S11-2 (BCL-) - Body ground | Ignition switch ON | Below 1 Ω |
|
| ||||
| OK | |
| 43.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S11-1 (BCL+) - Body ground | Always | 1 MΩ or Higher |
| S11-2 (BCL-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 44.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
|
| ||||
| OK | |
| 45.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 46.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly RH.
Using SST, connect S12-4 (BBR+) and S12-3 (BBR-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - A23-11 (BBP-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 47.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - A23-11 (BBP-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 48.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - Body ground | Ignition switch ON | Below 1 V |
| A23-11 (BBP-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 49.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A23-8 (BBP+) - Body ground | Always | 1 MΩ or Higher |
| A23-11 (BBP-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 50.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
|
| ||||
| OK | |
| 51.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly RH side and rear airbag sensor RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 52.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.
Using SST, connect S14-1 (BCR-) and S14-2 (BCR+) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 53.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the SST from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - S12-2 (BCR-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 54.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| S12-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 55.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| S12-1 (BCR+) - Body ground | Always | 1 MΩ or Higher |
| S12-2 (BCR-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 56.CHECK DTC |
![]() |
Connect the connectors to the center airbag sensor assembly and side airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 57.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the rear airbag sensor LH and the rear airbag sensor RH.
Replace the center airbag sensor assembly (Click here).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||